Publicidad
•
Use the highest position of the backrest only when the child is stable enough and does not lean.
INSTRUCTIONS AND WARNINGS FOR WORKING WITH BATTERIES - illustration B
Find the battery cover on the back of the mechanism. Use a screwdriver to loosen the cap screws. Take it off.
Insert 4 1.5 V type C (LR14) alkaline batteries (not included), observing the polarity marked on the bottom of the
compartment. Put the battery cover back on and tighten the screws with a screwdriver. Do not overtighten.
To remove the batteries, repeat the steps.
Note: Restart the electronics if the mechanism becomes unstable. Turn off the power button, remove the
batteries, and then insert them following the steps above.
IMPORTANT! The batteries are exhausted if the vibration and volume of the music weaken. Replace them with
new ones and dispose of used batteries in the designated area.
WARNING!
•
Only an adult should handle the batteries.
•
Keep children away from batteries. NEVER allow children to play with or charge the battery.
•
Always use new batteries.
•
If you are not going to use the product for a long time, remove the batteries.
•
Remove used batteries from the product and dispose of them in the designated areas, not in household waste
containers.
•
Do not dispose of batteries in a fire as there is a risk of explosion or leakage.
•
Non-rechargeable batteries are not to be recharged.
•
Use only the type of battery recommended by the manufacturer.
•
Different types of batteries are not to be mixed.
•
New and used batteries are not to be mixed.
•
Batteries are to be inserted with the correct polarity.
•
Do not place the battery or adapter for another product. This may result in overheating, fire or explosion.
•
Keep the adapter away from children.
•
Before you start charging the product you must check whether the adapter, battery and cables are in good
working order. If there is damage on any of these parts, you must stop using them, until the damage is
removed.
•
Do not let the battery discharge entirely. You must recharge it after each use or once a month if you are not
going to use it regularly.
Protect the environment by not disposing of this product in household waste
containers (2002/96 / EU). Check the recommendations of local authorities.
IMPORTANT! The diagrams and figures in this instruction are illustrative and indicative only.
Follow exactly the instructions and sequence for assembling and operating with the product.
Check the securing of the fixation after each operation.
Fixing a certain position in most cases is accompanied by a clicking sound.
Components - illustration A
After unpacking, make sure that all elements of illustration A are available.
1. Support base tubes - 2 pcs; 2. Rocking/music mechanism - 1pc; 3. Seat support frame -1 pc; 4. Bottom seat frame -
1 pc; 5. Connecting tubes for the upper frame - 2 pc; 6. Upper seat frame - 1 pc; 7. Toybar griff - 1 pc; 8. Seat body
cover (cusion, pillow, seat belt, cross and shoulders belt); 9. Remote control - 1 pc.
Assembly of the structure – illustration C
1. Base Assembly - Figure 1: Insert the base tubes (1) into the bottom of the rocker/music mechanism (2) as shown in
Figure 1. ATTENTION! Make sure the base is assembled correctly and is stable, this ensures the safety of your child!
2. Seat support frame assembly - Figure 2: Insert the seat support frame (3) into the top of the rocker/music
mechanism (2). When you hear a clicking sound, the assembly is complete.Note that if the frame is inserted incorrectly,
it will not lock to the base. It is important that the front and rear of the seat are correctly positioned as it has an anti-
tip function.
3. Assembling the bottom seat frame - Figure 3: Insert the bottom seat frame (4) into the openings of the installed
seat frame. When you hear a clicking sound, the frame is fixed.
4. Assembling the upper seat frame - Figures 4 and 5: Insert the connecting tubes (5) into the upper seat tube (6).
ASSEMBLY INSTRUCTIONS
16
Publicidad
