Ego Power+ LT0300E Manual página 6

Brightness Adjustment
EN
There are five brightness levels: 1 – 5 (600 lm – 3000 lm).
◾ Press the "+" button to increase brightness and press
the "–" button to decrease the brightness.
◾ When you turn on the light, the brightness will be the
same as the last time you used it.
Color Temperature Adjustment
You can adjust the color temperature of the light
according to your taste/needs.
◾ Press the " " button to toggle between the
following settings:
- Warm white light with a bias toward warmer tones,
- Warm white light with a bias toward cooler tones,
- Incandescent light,
- Warm yellow light
◾ When you turn on the light, the color temperature will
be the same as the last time you used it.
Mode Selection
An LED panel (or combination of LED panels) can be
turned on/off as desired.
◾ Press the "Mode" button to toggle between the
following modes:
- Area mode: all three LED panels are illuminated,
- Task mode: only the main (central) LED panel is
illuminated,
- Ambiance mode: only the two peripheral LED
panels are illuminated.
◾ When you turn on the light, the light mode will be the
same as the last time you used it.
◾ Press and hold the "MODE" button for 3 seconds and
the light will switch to flashing "SOS" mode. Press the
"MODE" button again and the light will return to the
previous brightness setting and panel selection.
NOTE:
In "SOS" mode, all 3 LED panels will be flashing,
even if before the "SOS" mode activation only some of the
LED panels were on.
NOTE:
When the temperature reaches 100°C, the main
(central) light LED panel will be turned off, and only the
two peripheral LED panels will be turned on to enter the
ambiance mode.
6
56 VOLT LITHIUM-ION CORDLESS AREA LIGHT-LT0300E
USING THE LIGHT (Fig. F1-F3)
WARNING:
Ensure the light is securely installed
to prevent falling object hazard. Failure to follow the
instruction can result in serious personal injury.
◾ To hang the light, pull out the hooks located in the
base of the unit and hang the light upside down.
The hook width is 1.7 in. (44 mm). Make sure the
object that the light is hung on is sturdy enough to
support the combined weight of the light and the
battery pack.
◾ To mount the light on a tripod (not included), secure
the tripod screw to the tripod mounting hole on the
bottom of the base. The base features a 1/4"-20
threaded hole. Make sure the tripod is placed on a
flat level surface.
WARNING:
Make sure the tripod is sturdy enough to
support the combined weight of the light and the battery
pack.
◾ For portable illumination, carry the light by the top
handle (Fig. D3).
POWERING USB DEVICES (Fig. E)
E-1 USB-C port
The USB-C port provides charging power of 5 Volts DC at
up a combined draw of 1.5 Amperes for your USB devices.
◾ Install a battery pack into the area light.
◾ Press the power button to turn the light ON.
◾ Insert one end of the USB-C cable (not included) into
the USB-C port and the other end into the device that
needs to be powered or charged. The light will begin to
charge/power the device automatically.
◾ When the light is not in use, disconnect the devices
from the light, then press the power button to turn it
OFF.
◾ Remove the battery pack from the light.
NOTE:
If the light is turned off during USB charging
process, the connected USB device will continue charging
for about 2 hours.
WARNING:
Runtime of the connected device is
dependent upon the device and the EGO battery capacity.
WARNING:
Do not insert a nail, wire, etc. into the
USB-C port. Otherwise a short circuit may damage the
USB-C port.