Publicidad
Idiomas disponibles
Idiomas disponibles
Read Operating Instructions
Please become familiar with all the instructions and
warnings before operating any pneumatic tool.
Visually inspect tool for damage and loose or missing
parts. If the equipment is worn or shows signs of
damage, remove it from service and contact an
authorized Sears service center for repairs.
Always Wear Approved Eye Protection
Impact resistant eye protection should meet or exceed
the standards set forth in ANSI Z87.1, Occupational and
Educational Eye and Face Protection. Look for marking
Z87.1 on your eye protection to ensure that it is an
approved style.
Hearing Protection is Recommended
Hearing protection should be used when the noise level
exposure equals or exceeds an 8 hour time-weighted
average sound level of 85dBA. Process noise, reflective
surfaces, other tools being operated nearby, all add to the
noise level in a given work area. If you are unable to
determine your noise level exposure, we recommend the
use of hearing protection.
Avoid Prolonged ER3osureto Vibration
Pneumatic tools can vibrate during usa. Prolonged
exposure to vibration or very repetitive hand and arm
movements can cause injury. Discontinue the use of any
tool if you experience tingling, numbness, discomfortor
pain in your hands or arms. You should consultyour
physician before resuming use of tool.
150 PSlG Maximum
This tool is designed to operate at an air pressure of 60
to 150 pounds per square inch gauge pressure (150
PSIG) maximum, at the tool. Use of higher air pressure
can and may cause injury.Also, the use of higher air
pressure placas the internal components under loads
and stresses they were not designed for, which could
cause premature tool failure.
NOTE: THE AIR SUPPLY SHOULD BE CLEAN, DRYAND
PREFERABLY LUBRICATED. FOR BEST RESULTS
DRAIN THE MOISTURE FROM YOUR COMPRESSOR
DAILY.
WARNING:
SOME DUST CREATED BY POWER SANDING, SAWING, GRIND-
ING, DRILUNG, AND OTHER CONSTRUCTION ACTIVFFIES
CONTAINS CHEMICALS KNOWN TO CAUSE CANCER, BIRTH
DEFECTS OR REPRODUCTIVE HARM. SOME EXAMPLES OF
THESE CHEMICALS ARE:
LEAD FROM LEAD-BASED PAINTS
CRYSTALLINE SILICAFROM BRICKS, CEMENTAND
OTHER MASONRY PRODUCTS
ARSENICAND CHROMIUM FROM CHEMICALLY
TREATED LUMBER
YOUR RISK FROM THESE EXPOSURES VARIES, DEPENDING ON
HOW OFTEN YOU DO THIS TYPE OF WORK. TO REDUCE YOUR
EXPOSURE TOTHESE CHEMICALS, WORK IN AWELLVENTI-
LATED AREAAN D WORK WITH APPROVED SAFETY EQUIPMENT
SUCH AS THOSE DUST MASKS THATARE SPECIALLY DE-
SIGNED TO FILTER OUT MICROSCOPIC PARTICLES.
FULL't'WO YEAR WARRANTY ON CRAFTSMAN
PROFESSIONAL AIR-DRIVE TOOLS
If this CraftsmanAir-DriveToolfails to give complete
satisfactionwithin two years from the date of
purchase,RETURN IT TO THE NEAREST SEARS
SERVICE CENTER/DEPARTMENT IN THE UNITED
STATES, and Sears willrepair it, free of charge. Ifthis
Craftsman toolis used for commercialor rental
purposes, thiswarranty applies for only 90 days from
the date of purchase,This warranty gives you specific
legal rights,and you may also have other rightswhich
vary from state to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman
Estates, IL 60179.
The Craftsman Model 875.204840 Continuous Flow
Grease Gun isdesigned for both automotive as well
as heavy industrial usage.
The Craftsman professionalContinuous Flow Grease
Gun Model 875.204840 is designed to operate at 60 to
150 PSI. Lower pressure will reduce the performance
of the tool, while pressure higher than the rated 150
PSI will damage the internal components to the tool.
• Exclusive air piston design assures self priming.
• Fully automatic; cycles continuous grease flow
when the trigger is depressed.
• Heavy duty spring for prime retention.
• High pressure performance with 60 to 150 PSI
generated at the compressor allows the tool to
deliver 2400 to 6000 PSI (40:1 ratio) of pressure
into the desired fitting.
Always use clean dry air. Excessive moisture and dirt
will greatly reduce the life of any air motor. We
recommend the installationof an in-linefilter-regulator-
lubricator as close to the tool as possible.
A 3/8" air hose is required up to a length of 8 ft. If
more length is required,a 1/2" air hose shouldbe
connected to the 3/8" hose to ensure the tool has the
necessary air supply.Be sure all hoses and fittings
are the correct size and tightlysecured.
Publicidad
