Publicidad
Idiomas disponibles
Idiomas disponibles
surfaces do not allow for safe handling and control of
the tool in unexpected situations.
5) SERVICE
a.
Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is
maintained.
⚠
ADDITIONAL SAFETY
WARNINGS
Wear hearing protection; Wear eye protection; Wear
dust mask; Wear protective gloves.
PRODUCT DESCRIPTION AND SPECIFICATIONS
Read instruction manual before using the tool
Read all safety warnings and all instructions, Failure
to follow the warnings and instructions may result in electric
shock, fire and/or serious injury.
INTENDED USE
The machine is designed for the chiselling of wood. The
machine is designed and constructed for use with
attachments supplied by the manufacturer. The machine can
only be used for dry applications without use of water.
Voltage
Power Rating
Frequency
Protection Class
Rated Speed
Mounting Thread Size
Weight
ASSEMBLY
⚠
WARNING: To reduce the risk of serious personal injury,
turn the tool off and disconnect from the power source
before making any adjustments or removing/installing tools
or accessories. Use protective gloves when handling the
chisels to prevent cuts and bruises.
a.
Inspect the Power Chisel to ensure that no damage has
occurred during shipping. If damaged, report to the
retailer immediately.
b.
The Power Chisel is packaged with spare chisels and an
Oil bottle. Remove a chisel from the package, wipe off
the protective coating and insert into the Chisel Arm
(2,7) with the chisel bevel and the interlocking notch
oriented as shown in Fig. C. When the chisel is aligned
and inserted correctly, it will snap firmly into place.
c.
To remove the chisel, first press the Chisel locking
button (3), then pull the chisel out of the arm as shown
in Fig. C.
d.
Use the oil bottle supplied to add 2 to 3 drops of oil in
the Oil Port (8) to lubricate the tool as shown in Fig. D.
e.
Apply 2 to 3 drops of oil from the supplied oil bottle to
Oil Port (8) at 15-minute intervals of tool use, and
before each initial use.
120
V
8.0
A
60
Hz
II
II
2 000 – 11 000
rpm
5/8"
inch
4.4
lbs
a.
Use suitable detectors to determine if utility lines are
hidden in the work area or call the local utility
company for assistance. Contact with electric lines can
lead to fire and electric shock. Damaging a gas line can
lead to explosion. Penetrating a water line causes
property damage or may cause an electric shock.
b. Release the ON/OFF switch and set it to the off
position when the power supply is interrupted e.g. in
case of a power failure or when the mains plug is
pulled.
c.
Do not touch chisels before they have cooled down.
The chisels can become very hot while working.
d. Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure than
by hand.
OPERATION
⚠
WARNING: The chisel shaft becomes very hot during
prolonged use. Use protective gloves to handle chisels. Hold
the chisels away from the cutting edge.
a.
The electric motor has been designed for the voltage
stated on the label. Always check the power supply
corresponds to the voltage marked on the motor.
b. Always wear correct safety clothing, including ear, eye
protective gloves and lung protection.
c.
Follow local government safety regulations when
working on materials treated with or containing toxic
substances.
d. Do not use this tool in wet conditions or in the
presence of flammable liquids and gases.
e.
Check tool before using. Test run the power tool with
no load prior to use. Do not use damaged tools.
Apply lubricant oil the Power Chisel every 15 minutes
f.
of use. As shown in Fig. D, apply lubricant from the Oil
bottle into the oil port.
Do no exert excessive pressure. The excessive pressure
g.
will overheat the chisel and the cam leading to
premature failure.
SWITCHING ON AND OFF
This power tool is equipped with lock-on switch. To start the
power tool, push the On/Off Switch (5) forwards (Fig. B) then
press it down at the front until it latches. To switch off the
tool briefly push down the back of the On/Off Switch and
release.
⚠
WARNING: The tool includes a restart prevention
feature, which prevents uncontrolled restarting after an
interruption to the power supply. To resume operation,
switch the tool to the off position and start the machine
again.
This power tool has variable speed control. Ensure an
appropriate speed setting is selected for the application
from the table below.
Publicidad
