Descargar Imprimir esta página

Delco Remy 37MT Hoja De Instrucción

Instalación de motores de arranque trabajo pesado
Ocultar thumbs Ver también para 37MT:

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

INSTALLING DELCO REMY HEAVY DUTY STARTING MOTORS (37MT, 40MT, 41MT, 42MT & 50MT)
WARNING!!!!ALWAYS USE PROPER EYE PROTECTION WHEN PERFORMING ANY MECHANICAL REPAIRS TO A VEHICLE –
INCLUDING, BUT NOT LIMITED TO, ANY INSTALLATION AND OR REPAIRS TO THE DELCO REMY
USE PROPER EYE PROTECTION CAN LEAD TO SERIOUS AND PERMANENT EYE DAMAGE.
Only perform the mechanical functions that you are properly qualified to perform. Mechanical repairs that are beyond your technical
capabilities should be handled by a professional installation specialist.
DANGER!!!
ALWAYS DISCONNECT BATTERY GROUND BEFORE REMOVING OR REPLACING CABLES AT THE STARTER.
FAILURE TO DISCONNECT THE BATTERY GROUND CABLE CAN LEAD TO SERIOUS INJURY.
NOTICE! FOLLOW ENGINE AND/OR VEHICLE MANUFACTURER'S INSTRUCTIONS CAREFULLY WHEN REMOVING AND
MOUNTING FLANGE HOLES AND BOLTS (Figures 1, 2 & 3, page 2)
This starter may have either .53" (13.6 mm) or .66" (16.8 mm) diameter mounting flange holes. Both starters can be mounted
with 1/2" or metric equivalent mounting bolts. Hex Head Cap Screws (Grade 5) should be used.
NOTICE! If Hex Head Size is too small, use a hardened washer or special 12-Point Head Cap Screw (Grade 5).
Do not use any lock washers, star washers or soft washers with the starter mounting bolts.
If any shims and/or spacer washers were used with the old starter, between the starter and flywheel housings, they must be
reinstalled in exactly the same location with this starter.
DRIVE HOUSINGS WITH ROTATABLE POSITIONING (Figure 1, page 2)
These starter types are provided with 12 or 24 positions for locating the solenoid, so that many models may be serviced with only a
few. This flexibility permits removing any interference of the solenoid upon installation. Repositioning can be accomplished by
removing the six (6) TORX nose housing bolts, rotating the switch housing and
reassembly. Torque bolts to 17.6-23.0 Nm (13-17 lb ft).
After rotation of starters using 5/8" mounting bolts, the lever housing boss may interfere with the wrench used for tightening. If this is
a problem, use a special 12-Point Head Cap Screw (Grade 5).
Solenoid must be mounted in an upward position for housing to drain. A few models have solenoids and drains inverted.
A heat resistant shield must be used if the solenoid is within two inches of the exhaust manifold.
INTEGRATED MAGNETIC SWITCH (IMS) REPOSITIONING (Figure 3, page 2)
Remove the two IMS mounting screws and loosen fasteners that attach the IMS leads to the solenoid, if necessary.
Reposition IMS by using a different set of solenoid mounting screws and/or set of bracket holes to obtain clearance.
Reinstall mounting screws and torque all fasteners according to values labeled in figure 3, page 2.
GROUNDING INSULATED STARTING MOTORS (Figures 2 & 3, page 2)
This may be an insulated starter replacing a grounded type starter. Insulated starters have a flexible cable connecting the solenoid
ground terminal to terminal on the commutator end of the starter (labeled Insulated/Ground). An insulated starter must have a cable
connecting this terminal to the battery ground (-) connection for the starter to function. This grounding cable between the starter and
battery should be a copper cable the same size as the positive (+) battery cable being used.
ELECTRICAL CONNECTIONS (Figures 2 & 3, page 2)
Identify and tag all leads when removing old starter so they can be properly connected on the new starter. Be sure to connect the
cables to correct solenoid terminals, because the terminals may be reversed.
Clean or wire brush all terminals so that bare metal is exposed for good electrical connections.
The connector for starters with optional Over Crank Protection (OCP) is the same for all series of starters.
Tighten all fasteners according to torque values labeled on the illustrations.
RING GEAR
If the ring gear is damaged, it must be replaced to avoid a potential early failure and risk rejection of a warranty claim.
NOTICE
- Only licensed Delco Remy products and component parts should be used, and the use of other parts or modifications not approved by PHINIA
will void all applicable warranties. The failure to carefully follow these Instructions, set forth herein, will void all applicable warranties. DELCO REMY is a
registered trademark of General Motors LLC, licensed to PHINIA Technologies Inc.
© 2023 PHINIA Inc. All rights reserved
INSTALLING THE STARTERS.
1
Hoja de Instrucción
10511650
08FE24 C0008709 REV8
®
PRODUCTS. FAILURE TO

Publicidad

loading

Resumen de contenidos para Delco Remy 37MT

  • Página 1 NOTICE - Only licensed Delco Remy products and component parts should be used, and the use of other parts or modifications not approved by PHINIA will void all applicable warranties. The failure to carefully follow these Instructions, set forth herein, will void all applicable warranties. DELCO REMY is a registered trademark of General Motors LLC, licensed to PHINIA Technologies Inc.
  • Página 2 NOTICE - Only licensed Delco Remy products and component parts should be used, and the use of other parts or modifications not approved by PHINIA will void all applicable warranties. The failure to carefully follow these Instructions, set forth herein, will void all applicable warranties. DELCO REMY is a registered trademark of General Motors LLC, licensed to PHINIA Technologies Inc.
  • Página 3 NOTICE - Only licensed Delco Remy products and component parts should be used, and the use of other parts or modifications not approved by PHINIA will void all applicable warranties. The failure to carefully follow these Instructions, set forth herein, will void all applicable warranties. DELCO REMY is a registered trademark of General Motors LLC, licensed to PHINIA Technologies Inc.
  • Página 4 Apriete todas las tuercas de acuerdo con los valores de par indicados en las ilustraciones. NOTA - Solamente deben ser usados productos y componentes Delco Remy, el uso de otras partes o modificaciones no aprobadas por PHINIA anulará todas las garantías aplicables. No seguir cuidadosamente las instrucciones de instalaciones expuestas en este documento anulará...
  • Página 5 Delco Remy recomienda encarecidamente el uso de un cable de tierra.. NOTA - Solamente deben ser usados productos y componentes Delco Remy, el uso de otras partes o modificaciones no aprobadas por PHINIA anulará todas las garantías aplicables. No seguir cuidadosamente las instrucciones de instalaciones expuestas en este documento anulará...
  • Página 6 NOTA - Solamente deben ser usados productos y componentes Delco Remy, el uso de otras partes o modificaciones no aprobadas por PHINIA anulará todas las garantías aplicables. No seguir cuidadosamente las instrucciones de instalaciones expuestas en este documento anulará todas las garantías aplicables. DELCO REMY es una marca registrada de General Motors Corporation autorizada bajo licencia de PHINIA Technologies Inc.
  • Página 7 AVIS pas approuvées par PHINIA annulera toutes les garanties applicables. L’enfreindre de ces instructions d’installation annulera toutes les garanties applicables. DELCO REMY est une marque registrée de General Motors Corporation, licenciée d’a PHINIA Technologies Inc. © 2023 PHINIA Inc. Tous les droits réservés.
  • Página 8 (-) à la terminale isolée/de terre sur les moteurs de démarrage qui disposent d’un, comme il a été retiré du moteur de démarrage vieux. Delco Remy recommande fortement l’usage d’un câble de terre. Connectez le câble de terre (-) à la terminale isolée/de masse sur les moteurs de démarrage qui disposent d’un, comme il a été...
  • Página 9 AVIS pas approuvées par PHINIA annulera toutes les garanties applicables. L’enfreindre de ces instructions d’installation annulera toutes les garanties applicables. DELCO REMY est une marque registrée de General Motors Corporation, licenciée d’a PHINIA Technologies Inc. © 2023 PHINIA Inc. Tous les droits réservés.

Este manual también es adecuado para:

40mt41mt42mt50mt