Publicidad
Idiomas disponibles
Idiomas disponibles
Rotational speed:
Torque:
Gear 2 :
Suitable for:
Rotational speed:
Torque:
8.6
Set direction of rotation
ATTENTION
The direction of rotation switch may only be actuated
when idle.
With the direction of rotation switch, you can select the di-
rection of rotation of the product (clockwise or anti-clock-
wise) and secure the product from being switched on un-
intentionally. The arrow on the direction of rotation switch
indicates the working direction.
1. Wait until the product has come to a standstill.
2. Push the direction of rotation switch (10) to the de-
sired position:
– Clockwise rotation: For drilling and screwing
in screws. Press the direction of rotation switch to
the right.
– Anti-clockwise rotation: To undo screws. Press
the direction of rotation switch to the left.
3. Switch lock: Put the direction of rotation switch in the
centre position.
8.7
Adjusting the torque
ATTENTION
The torque adjusting ring may only be actuated when
idle.
Note:
A clear ratcheting sound is heard when reaching the pre-
set torque limit. This noise is caused by the slip clutch.
Note:
You can preset the maximum torque by turning the torque
adjusting ring (3). There are 25 torque levels + 1 drill lev-
el.
1. Select the desired torque by turning the torque adjust-
ing ring (3).
2. Start with a lower torque level and increase it as re-
quired.
Level 1
Level
Screws
Drilling
8.8
On/Off switch (9) (Fig. 1)
The speed can be steplessly controlled by the on/off
switch. The further you press the on/off switch, the higher
the speed.
1. To switch on the product, push the on/off switch (9).
2. To switch off, release the on/off switch (9).
Low
If you put the direction of rotation switch (10) in the
High
centre position, the product is secured from being
switched on.
0 - 1600 rpm
8.8.1
Drilling work
This product is equipped with an LED work lamp to illumi-
High
nate the immediate work area and improve visibility in
Low
poorly lit environments.
Do not look directly into the LED work lamp or the light
source.
1. The LED work lamp (8) lights up automatically as
soon as the product is switched on.
Note:
The LED work lamp remains lit up for approx. 10 seconds
after the product is switched off.
8.8.2
1. During work breaks, the product can be hooked onto
the belt with the integrated belt clip (11).
Note:
Make sure that the product is switched off and secured
against being switched on.
9
Have maintenance and repair tasks that are
not described in this operating manual, car-
ried out by a specialist workshop. Use only
original spare parts.
There is a risk of accident! Always perform
maintenance and cleaning work with the bat-
tery removed. There is a danger of injury! Let
the Product cool down before all mainte-
nance and cleaning tasks. Elements of the
engine are hot. There is a danger of injury
and burning!
The product can start unexpectedly and cause injuries.
–
Remove the battery.
–
Allow the product to cool down.
–
Remove the tool attachment.
Lowest torque
Highest torque
9.1
Level 1 - 25
1. Keep protective devices, air vents and the motor
housing as free of dust and dirt as possible. Rub the
Level
product clean with a clean cloth or blow it off with
compressed air at low pressure. We recommend that
you clean the product directly after every use.
2. Ventilation openings must always be free.
3. Do not use any cleaning products or solvents; they
could attack the plastic parts of the product. Make
sure that no water can penetrate the product interior.
www.scheppach.com
LED work lamp (8)
CAUTION
Applying the belt clip (11)
Cleaning and maintenance
WARNING
Cleaning
GB | 19
Publicidad
