SUHNER ABRASIVE ROTOmax 2.2 Documentación Técnica página 35

2.2.4 s
Afety guArd
If a safety guard is supplied with the hand tool, it is
imperative that the safety guard be used.
2.3 r
Ating dAtA
2.3.1 s
pecificAtions
Voltage
Power Input
Power Output
Protection class
Type of protection
Overload protection
No-load speed
Sound pressure level
Threaded connection for flexible shafts of type:
DIN 10
NA 4, NA 7, NA 10, NA 12
NA 10 DIN 10/G28 STEP
NA 12 DIN 10 G28 STEP
2.3.2 V
iBrAtion mesurement VAlues of hAnd tools
BSG 10
Measurement value <2.5m/s
FSM 1:1
Measurement value 4.7m/s
WI 7, WI 10
Measurement value <2.5m/s
WH 12
Measurement value <2.5m/s
FH 12
Measurement value <2.5m/s
FH 10
Measurement value <2.5m/s
FH 7, FH 4
Measurement value <2.5m/s
According to ISO/EN 60745.
The specified vibration value was measured with a
standardised test method and may differ from the
actual operating value. The specified value can be
used for product comparisons or for an introductory as-
sessment of work breaks.
2.4 o
perAting conditions
Temperature range during operation: 0 to +50°C
Relative air humidity: 90% at +30°C, 65% at +50°C
1x230/240V - 50/60Hz, 8.9A
2000W
1650W
IP45
yes
500-13'000min
77dB(A), K=1.5dB(A)
M10
see catalog
03002613
03002912
Test grinding wheel ø 100x25
/K=1.5m/s
2
Drive 7'000min
Test grinding wheel ø 180x6
/K=1.5m/s
2
Drive 8'000min
Test grinding wheel ø 50x6
/K=1.5m/s
2
Drive 15'000min
Test grinding wheel ø 100x25
/K=1.5m/s
2
Drive 10'000min
Test grinding wheel ø 80x10
/K=1.5m/s
2
Drive 12'000min
Test grinding wheel ø 80x10
/K=1.5m/s
2
Drive 15'000min
Test grinding wheel ø 25x10
/K=1.5m/s
2
Drive 15'000min
To avoid strong looping movements and beaming
of the flexible shafts, the working pressure must
be reduced.
3.
haNDLINg
3.1 m
Achine
1 3.1.1 c
ontrol KeypAd
-1
2
Speed display (1). Memory locations «1-5» (2). Free speed
«F» (3). Speed correction «+/-» (4). Start command «run»
2
(5). Stop command «stop» (6).
-1
3.1.2 s
2
tArting the mAchine
Before turning on the machine, make sure to re-
-1
move wrenches and adjusting tools.
When turning on, hold the flexible shaft extended.
2
During operation make sure that the flexible shafts have
-1
large bend radius.
Before starting the machine, hold the hand tool against
2
turning!
-1
Five different speeds can be stored under the «1-5» keys
for each threaded connection. The speed of the «F» key
2
applies to both threaded connections.
-1
If not all of the «1-5» keys are required, a memory location
can be set to the value «zero».
2
If any key (except the «+/-» key) is pressed while the ma-
-1
chine is running, an immediate stop is made. The display
flashes. Before restarting, the key with the correct speed
2
must first be pressed.
-1
Press the main switch (1) of the machine.
/ o
PERaTIoN
35