Publicidad
Idiomas disponibles
Idiomas disponibles
WARNING:
Prior to hanging the bulbs, make sure they do not rest upon any hot surface or where they could
become damaged. If you are charging the batteries without attaching the bulbs, keep the bulbs in
the retail box or safely store them indoors to prevent any potential damage.
CAUTIONS: SAFETY INFORMATION
• Your solar string lights are not a toy. Keep them out of reach of small children.
• Your solar string lights and solar panel are both fully weather-resistant.
• The solar panel must be mounted outdoors to maximize sun exposure.
• Prior to installation, lay out all components and check against the parts list section of this manual.
• Never look directly into the solar string lights.
• Do not hang any other objects on the solar string lights.
• Do not cut the wire or make any wiring changes to the solar string lights.
CAUTIONS: BATTERY INSTRUCTIONS
When replacing the batteries for the solar string lights, be sure to:
• Use rechargeable batteries only.
• Match the replacement battery specifications with the batteries that have been removed.
• Observe the correct polarity (+/-) when installing the replacement batteries.
Refer to page 3, step 7 for further details.
PRODUCT FEATURES
• Vintage looking LED light bulbs
• Integrated mounting loops
• Solar battery charging
PRE-INSTALLATION
The solar string lights are shipped with the batteries pre-installed. Before starting any
1)
installation, test the bulbs for illumination.
2)
Ensure your solar panel is placed
so that its exposure to sunlight is
optimized. Be aware of objects such
as trees or property overhangs that
may impede the panel's ability to
generate a charge.
• Automatic illumination at dusk
• 60.9 cm / 2 ft bulb spacing
• 13.1 m / 43 ft total cable length
a)
Connect the solar panel to the connector on
the string lights.
Turn the solar panel over so the glass solar
b)
collector is facing down on a flat surface. It is
best to use a cloth for this to prevent scratching
the solar glass. No light should be detected on
the solar glass.
c)
Select ON on the back of the solar panel.
d)
The bulbs should now illuminate.
Once the bulbs are all illuminated, turn the switch
to OFF and continue with the installation.
3)
MOUNTING THE SOLAR PANEL: THE SOLAR PANEL HAS TWO MOUNTING OPTIONS
MOUNTING BRACKET
If required use the two
(1)
wall plugs (H) along with
the two large screws (G).
Install the screws utilizing
the two outer holes of the
mounting bracket to secure
the bracket to the chosen
surface.
Insert the mounting base
(2)
(D) onto the back of the
solar panel (B). Use the
included small screw (F) to
tighten the connection.
Slide the solar panel down
(3)
(5)
The angle of the solar
onto the mounting bracket
panel can be adjusted to
(E) until you feel and hear
maximize sun exposure
the connection click into
by loosening, adjusting
place.
and then re-tightening the
Adjust the solar panel
side screw located on the
(4)
to the desired angle to
solar panel's protruding
optimize sun exposure.
arm.
Note: To disconnect the solar
panel from the mounting
bracket, press down on the
release tab on the bottom of the
mounting bracket. With the tab
firmly pressed, slide the solar
panel upwards and free of the
bracket. Some force may be
required to remove the panel
from the bracket.
GROUND STAKE
To utilize the ground stake (C), connect the two parts of the
stake together.
The grooved section then fits into the protruding arm of the
solar panel. The stake can then be used to mount the panel
into the ground.
Prior to using your solar string lights, the solar panel
needs sunlight for a period of three days. This initial
charge should be done without the string lights
connected or with the solar panel in the OFF position.
After the third day, your included batteries will be
fully charged.
Note: The solar panel should be mounted in a place
where the ON/OFF switch is easily accessible.
Publicidad
