MESTIC MPS-600 Instrucciones De Uso página 25

Error codes
Error no. Fault description
1 Serious battery fault
2 Pressure difference is too large
3 BMS voltage fault
4 Battery OTP (over temperature protection) fault
5 Battery UTP (under temperature protection) fault
6 OCP (over current protection) fault
7 OTP fault
8 Pre-charge fault
9 Battery under voltage fault
10 Abnormal parellelization
11 Abnormal INV battery voltage
12 Grid voltage or frequency fault
13 Abnormal INV BUS voltage
14 Abnormal INV output
15 INV discharge overload
16 Charge overload
17 INV Tz
18 Battery short
19 INV output short
20 MOSFET OTP fault
21 Fan stop
22 Discharge soft start fault
23 Charge soft start fault
24 MOSFET UTP fault
25 Anderson hardware OCP fault
26 Anderson software OCP fault
27 PV hardware OCP fault
28 PV1 software OCP fault
29 PV2 software OCP fault
30 Car charge output OCP fault
31 PV output OVP (over voltage protection) fault
32 PV1 input OVP fault
33 PV2 input OVP fault
34 Anderson OTP fault
35 PV1 OTP fault
36 PV2 OTP fault
37 Car charge output OTP fault
38 Abnormal communication
39 Abnormal USB
40 Abnormal type C
Disclaimer
1. The product has a built-in battery management system with protections such as overcharge, over-
discharge, overcurrent, short circuit, high and low temperature, and abnormal communication. During the
use of this product, protection may occur, causing output interruption. The power supply to special
equipment, such as medical equipment or servers, and any indirect loss caused by accidental power failure,
we do not take responsibility for. All accidents caused by illegal use, self-dismantling, and man-made
damage we do not take responsibility for.
2. Before using the power station, please read this user manual to ensure understanding and proper use.
Keep the user manual for future reference. Improper operation may cause serious injury or result in
product damage and property loss. By using the power station, you are deemed to have understood and
accepted all terms and contents herein. Users promise to be responsible for their actions and all
consequences arising therefrom. The company shall not be liable for any loss arising from the user not
following this user manual.
3. In compliance with laws and regulations, the manufacturer reserves the right of the final interpretation of
this document and all related documents of this product. Subject to update, revision, or termination
without prior notice, please visit the official website for the latest product information.
Solution
Turn on and off. Contact customer service if not fixed.
Auto shutdown. Fault will be cleared after reboot.
Auto shutdown. Temperature recovery enables starting up.
Auto shutdown. Remove the over-power device. Fault will be cleared after
reboot.
Auto shutdown. Delayed start.
Auto shutdown. Fault will be cleared after reboot.
Auto shutdown and charge. Contact customer service if still not fixed after
multiple charging failures.
Check the connection cable. Contact customer service if still not fixed.
Single power station function is not affected.
Auto recover after fault is cleared.
The fault is cleared when the grid returns to normal.
Auto recover after fault is cleared.
Remove over-power device. Auto recover after fault is cleared.
Auto recover after fault is cleared.
Fault will be cleared after reboot.
Auto recover after product has cooled down.
Turn on and off. Contact customer service if not fixed.
Auto recover after fault is cleared.
Turn on and off. Contact customer service if not fixed.
Remove PV charge. Auto recover after connection PV and turning on.
Turn off output. Manual recover after fault is cleared.
Remove PV charge. Auto recover after connection PV and turning on.
Stop PV1 charging. Auto recover after connecting PV and turn on.
Stop PV2 charging. Auto recover after connecting PV and turn on.
Turn off output. Manual recover after fault is cleared.
Stop PV. Auto recover after fault is cleared.
Stop PV1. Auto recover after fault is cleared.
Stop PV2. Auto recover after fault is cleared.
Turn off output. Manual recover after fault is cleared.
Stop PV1. Auto recover after fault is cleared.
Stop PV2. Auto recover after fault is cleared.
Turn off output. Manual recover after fault is cleared.
Turn on and off, or change operation environment. Contact customer
service if still not fixed.
Auto recover after removing abnormal USB.
Auto recover after removing abnormal type C.