KidKraft FINI2 Manual De Usuario página 18

WARNING!
• This product is intended for babies between the ages of 24 and 60 months,
weighing up to 20 kg, who are able to sit up unaided.
• DO NOT place this product near a window as it can be used as a step by the
child and cause the child to fall out of window.
• Be aware of the risk of open fires and other sources of strong heat in the
vicinity of the product
• DO NOT place this product near a window where cords from blinds or curtains
could strangle a child
• All assembly fittings should always be tightened properly
• not to use seating if any part is broken, torn or missing and use only spare parts
approved by the manufacturer
• the restraint system shall be removed/hidden/covered when the product is used
as a seating for older children.
Main parts
1.‫ي‬Seat‫ي‬with‫ي‬attached‫ي‬safety‫ي‬belts
2.‫ي‬Front‫ي‬upper‫ي‬legs‫ي‬with‫ي‬plastic‫ي‬elements‫ي‬for‫ي‬fixing‫ي‬the‫ي‬footrest‫ي‬x2
3.‫ي‬Rear‫ي‬upper‫ي‬legs‫ي‬x2
4.‫ي‬Lower‫ي‬legs‫ي‬x4
5.‫ي‬Tray‫ي‬with‫ي‬a‫ي‬plastic‫ي‬cover‫ي‬
6.‫ي‬Double-sided‫ي‬footrest
7.‫ي‬Armrests‫ي‬x2
8. Bolts (for affixing the front top legs) x 2
Assembly of the high chair
Screw the front upper legs with plastic elements for fixing the footrest (2) into holes located in the front of the seat (1)
(Figures A and B). Make sure that plastic elements are on inside parts of legs. Next, turn the seat with the legs screwed
in. Screw the bolts (8) to the legs in the openings in the correct part of the seat (figure C). Select the position of the
footrest (6) in accordance with the size of your child. The variant presented in Figure D1 is dedicated to smaller children.
The variant in Figure D2 is dedicated to larger children. Slide the footrest (6) into plastic elements on inside parts of legs
(Figure E). You will hear a characteristic click sound. Then screw the rear upper legs (3) into holes located on the back
of the seat (1) (Figures F and G). Tighten the front and rear lower legs (4) (Figure H). Adjust feet located at the end of
lower legs in order to ensure that the entire oblique plane adheres to the floor (Figure I).
Fixing and adjusting the tray
In‫ي‬order‫ي‬to‫ي‬mount‫ي‬the‫ي‬tray‫ي,)5(ي‬slide‫ي‬it‫ي‬into‫ي‬the‫ي‬guides‫ي‬while‫ي‬pressing‫ي‬the‫ي‬button‫ي‬on‫ي‬the‫ي‬front‫ي‬of‫ي‬the‫ي‬tray‫(ي‬Figure‫ي‬J).‫ي‬To‫ي‬
adjust‫ي‬the‫ي‬tray,‫ي‬press‫ي‬the‫ي‬button‫ي‬and‫ي‬select‫ي‬one‫ي‬of‫ي‬three‫ي‬settings‫(ي‬Figure‫ي‬J).
The‫ي‬tray‫ي‬has‫ي‬a‫ي‬plastic‫ي‬removable‫ي‬insert‫(ي‬Figure‫ي‬K).
Use of adjustable safety belts
Adjustment:
18