AEG WSL 125 XS Instrucciones De Uso página 2

GB
Your standards are high and you have opted for
quality from Atlas Copco.
Make good use of your new electric power tool, we
have built it with great care, but first read the
instruction booklet.
1 Illustrations
1 Spindle lock
2 Gear neck
3 Working spindle
4 Screw
5 Guard
6 Back flange
7 Working tool
8 Flange nut
9 Steel–wire brush (Accessory*)
10 On-/off switch
11 Additional side handle
12 Backing pad (Accessory*)
13 Abrasive paper (Accessory*)
14 Clamping flange (Accessory*)
15 Guide shoe and Wheel guard (Accessory*)
*Not included in standard equipment, available as an accessory
2 Technical data
Nominal power . . . . . . . . . . . . . . . . .
No-load speed . . . . . . . . . . . . . . .
Grinding disc diameter
Backing pad diameter
Thread of working spindle
Weight . . . . . . . . . . . . . . . . . . . . . . . . .
3 Safety Instructions
Please note safety instructions on red sheet
4000 3330 24!
Appliances used at many different locations
including open air must be connected via a
current surge preventing switch.
Always wear goggles when using the machine. It
is recommended to wear gloves, sturdy non
slipping shoes and apron.
Do not pierce the motor housing as this could
damage the double insulation (use adhesives).
Always disconnect the plug from the socket
before carrying out any work on the machine.
Keep mains lead clear from working range of the
machine. Always lead the cable away behind you.
Only plug-in when machine is switched off.
Always use the additional handle.
Only use diamond cutting discs that are sharp
and in perfect condition. Replace diamond cutting
discs at once if they have splits or are deformed.
Accessories must be limited to 10,000 rpm.
1
WSL 115 XS WSL 125 X
710 W
10 000 min
. . . . . . . . . . . 115 mm
. . . . . . . . . . . . 110 mm
. . . . . . M 14 mm
1,6 kg
A power tool only performs at its best when
properly handled.
AEG Electric Power Tools from Atlas Copco
WS 100 S
. . . . 710 W . . . . . 710 W
–1 –1
10 000 min 10 000 min
. . . 125 mm . . . 100 mm
. . . 110 mm . . . . .
. . M 14 mm . . M 10 mm
. . . . . 1,6 kg . . . . . 1,6 kg
When cutting stone, a guide has to be used.
Always use guard when grinding or cutting.
Due care should be taken that sparks flying from
the work piece do not contact inflammable
materials.
Before setting the machine into motion tighten
flange nut.
In special cases e. g. when the machine is used
under extreme humid conditions or is very
contaminated with conductive dusts, we
recommend the use of an ELCB safety switch
(earth leakage circuit breaker) to increase your
personal safety.
Typically the A-weighted sound pressure level of
the tool is 85 dB (A).The noise level when
working can exceed 85 dB (A). Wear ear
protectors!
Typically the weighted acceleration is :
2 (
3 m/s WSL 115 XS, WS 100 S, WS 115 S)
2 (
4 m/s WSL 125 X, WS 125 S)
Do not use this product in another way as stated
for normal use.
WSL 115 XS, WSL 125 X, WS 100 S, WS 115 S, WS 125 S
WS 115 S
. . . . 710 W . . . .
–1 –1
10 000 min
. . . . 115 mm
– . . . . . . . . 110 mm
. . M 14 mm
. . . . . 1,6 kg . . . . .
WS 125 S
710 W
–1
10 000 min
. . . 125 mm
. . . 110 mm
. . M 14 mm
1,6 kg