Profi Care PC-HBB 3117 Manual De Instrucciones página 9

Warnings for the Use of the Appliance
• To prevent the appliance from overheating, the appliance
should not be covered. Keep the ventilation slots free.
• The motor unit and the bars become hot during operation.
Therefore, do not touch them during or shortly after use.
• Do not leave the appliance unattended for hours. Do not
leave the house during operation.
Notes for Use
• The appliance is intended for garments which are spin-
dried by a washing machine. Allow the garment to drain
in case you wash it by hand or if you haven't spin-dried it.
The appliance is not suitable for dripping wet clothes.
- For best results, use ironing moist clothes.
• The drying time depends on the material of the garment.
• If necessary, the placket, cuffs and the collar need to be
ironed once more. For trousers, it may be necessary to
iron the waistband, the hem and the area around the
zipper.
• Conventional clothespins may be used for fixing the
garments to the balloon body. When using extra long
garments, clothespins are of advantage in order to en-
sure the best possible drying at the projecting edge.
On / Off Switch
The functions of the on / off switch are the following:
ON =
Appliance in continuous operation
OFF = Switch off the appliance
30 – 180 = Timer operation in minutes
Safety Switch
Your appliance is equipped with a safety switch. This cuts
off the power supply as soon as the appliance is tilted by
45 °. The safety switch can prevent dangerous situations
caused by overheating.
Electrical Connection
Check whether the mains voltage that you want to use,
corresponds with that of the appliance. You will find the
information about it on the rating plate.
Assembly
Preparation
1. Mount the hanger by inserting the hanger arms into the
head of the hanger. Watch out for the markings left (L)
and right (R) (see image).
2. Use the provided screws to attach the hanger arms at
the bottom of the hanger.
PC-HBB3117_IM
3. Place the motor unit on a flat, non-slip and heat-resistant
surface.
4. Insert the short pole into the appliance in such a way
that the marking points show downwards.
5. Slide the fan cover onto the pole until it reaches the
marking.
6. Attach the joint onto the short pole with the joint and
both its openings pointing upwards.
7. Insert the two longer poles into the openings of the joint.
Mounting the Rack for Shirts
8. Mount the hanger on the poles. Use the two outer
openings for this.
9. Loosen the two connectors on the two poles and pull
the poles to the desired height. Tighten the connectors
again.
10. For shirts, put the balloon body over the hanger and
pull it over the rack. Use the elastic band to secure the
balloon body to the mounting device.
The appliance is now ready to use.
Mounting the Rack for Trousers
8. Loosen the two connectors on the two poles and pull
the poles to the desired height. Tighten the connectors
again.
9. For trousers, put the balloon body over the poles. Each
trouser leg of the balloon body must hang over one pole.
Use the elastic band to secure the balloon body to the
mounting device.
The appliance is now ready to use.
Operation
1. Set the on / off switch to the OFF position.
2. Pull the garment (e. g. shirt) over the balloon body. Note
the following when doing so:
• The collar must be placed above the balloon body's
collar part.
• All buttons of the garment need to be buttoned.
• The garment must lie flat on the balloon body.
3. Insert the mains plug into a correctly installed safety
socket.
4. Turn the appliance on by using the on / off switch. There
are two ways for operating the appliance:
1) Set the on / off switch to ON.
2) Set a time with the on / off switch.
- The indicator lamp lights up when the appliance is in
operation.
5. Switch the appliance off by setting the on / off switch to
OFF.
6. Disconnect the mains plug from the socket.
7. Allow the garment to cool down before removing it from
the balloon body.
9
10.10.23