Kerbl BA-1332 Manual De Instrucciones página 7

Specific Operating Instructions
This completely new designed, High-Performance-Fence-Energizer owns an intelligent POWERtronic-technology,
which gives you the possibility of an automatic power-adaptation of your fence-system. POWERtronic achieves excellent
fencing security with minimal current consumption and offers unique and maximimal flexibility and a variety of
combinations of power sources, such as 12V, 12+solar and mains supply. Of course the solar-charge-regulator is
already integrated with POWERtronic.
POWERtronic - the future-orientated technology - is already available to you today.
a.)
2
9
1
c.)
Operating modes:

On- / Off switch: Press operating knob (2) as long (approx. 3sec.) as
Display

By turning the operation knob the display goes into the adjustment-mode, the power-levels can now be adjusted

The actual voltage of the current-source is shown by short pressing of the operating knob during the OFF-
condition or during normal operation.
Possible current-sources:
- 12 Volt (approx.80-85Ah) accumulator (ideal value: 12,6 – 13,8V)
Optional additionally with solar-modules possible ( max. 50W solar-module
- special 230 Volt mains-adapter No. 371012 (keeps charging status but not suitable for recharging the 12V
accumulator)
LCD-display (5)
Adjustment-mode
12V: 1 to 20
Mains adapter resp.
Solar-module supplies current
b.) Starting the appliance without fence and earth connection:
General:
The appliance is opened by mutual opening of the closing-tabs (8).
Close the appliance solidly before a new start. Operate only in up standing position; see above picture (b).
12V - operation
Always connect first the enclosed 12V - or - connection cable to the battery or the accumulator. Pay attention on correct
polarity (red + and black -) when connecting the battery or the accumulator. Than put the battery or the accumulator into
the housing, lead the ventilation tube of the accumulator (if existing) outside through the gap! Now connect the plug of the
connection cable with the plug (9) at the top casing. Start the appliance by longer pressing (approximately 3sec.) of the
operating knob (2) without fence and earth.
If the fence voltage indicator light (4) flashes green and a voltage of higher 4kV is indicated on the display, the appliance
is ready to start. If the battery indicator light (3) flashes red additionally, then the battery should be recharged soon resp.
being replaced soon. If only the battery indicator light (3) flashes red and the indicated fence-voltage is 0.0, this means
that the battery has to be changed resp. the accumulator has to be recharged without any delay. If none of the indicator
lights is blinking and no value is indicated on the display, first check the polarity of the connection cable at the current-
source resp. contact your expert for a check.
In case of operation with a solar-module / mains adapter (see below b.) the accumulator / battery should always be
connected, before the solar-module / mains adapter is connected to the solar-socket (otherwise the danger of a short
circuit exists). Before connecting to the fence, switch OFF the appliance with the operating knob (2) and switch ON only
after connection again.
4 b.)
3
5
This energizer shall not be used as an
animal trainer (inside a barn).
7
6
: power-levels
1
8
2 Operating knob
3 Battery indicator light
4
5
6 Earth connection
7 Fence connection
8
9
Display-mode:
Voltage of accumulator / battery
V
7.7
Display-value
kV
Display-mode:
Exit-voltage in kV
7,7kV = 7700 Volt
5
Solar / 230V mains adapter
connection
continuously
adjustable power control
Fence voltage
indicator light
LCD - display
Closing-tabs
(for closing / to shut cover and housing)
battery cable
kV appears right below on the LCD -
connection (1) )
-EN-
Version : 2020.1