Symbols Used On The Appliance; Getting To Know The Appliance; Handling The Packed Appliance; Unit Of Measurement - Fimap FM43 ORBITALE EXTRA SPRAY Manual De Uso

14. SYMBOLS USED ON THE APPLIANCE

Appliance's earth symbol:
Indicates the earth connection point of the appliance's electric system.
Maximum gradient symbol:
X%
Indicates the maximum gradient.

15. GETTING TO KNOW THE APPLIANCE

15.1. HANDLING THE PACKED APPLIANCE

The appliance is contained in two packages, the packing elements (plastic bags, staples etc.) should
be kept out of the reach of children and incapacitated adults etc.
The overall weight of the two packages is 50 kg (components plus packaging).
The dimensions of the two packages are as follows:
Unit of BRUSH
HANDLEBAR
Measurement HEAD
A mm 340
B mm 510
C mm 720

15.2. HOW TO UNPACK THE APPLIANCE

The machine is contained in two separate packages, one for the handlebar and the other for the brush
head body.
To remove the brush head from the packaging proceed as follows:
1. Place the lower part of the outer packaging in contact with the floor.
WARNING: Handle the packed product with suitable lifting devices that comply with legal
requirements.
2. Open the box removing the adhesive tape.
CAUTION: users are advised to always wear protective gloves, to avoid the risk of serious injury
to hands.
3. Remove the brush head from the pack.
To remove the handlebar from the packaging proceed as follows:
1. Place the lower part of the outer packaging in contact with the floor.
2. Open the box removing the adhesive tape.
CAUTION: users are advised to always wear protective gloves, to avoid the risk of serious injury
to hands.
3. Remove the handlebar and the spray kit from the packaging.

15.3 HOW TO TRANSPORT THE APPLIANCE

To transport the machine, proceed as follows:
1. Check that the plug (1) on the power cable (2) has been taken out of the socket (3) of the mains
supply(Fig.1), and if not, disconnect it.
CAUTION: users are advised to always wear protective gloves, to avoid the risk of serious injury
to hands.
WARNING: To prevent damaging the power cable, disconnect the plug from the mains socket by
directly pulling the plug and not the cable.
2. Check that the handlebar is in the vertical position, if not, press the uncoupling lever (4) (Fig.2)
and turn the handlebar to the vertical position (Fig.3). When the handlebar is vertical, release the
uncoupling lever (4).
3
1
2
1 2
3. Disconnect the power supply connector of the brush head motor (5) from the power connector (6)
on the control handlebar (Fig.4).
4. Remove the knob (7) that fixes the nozzle support bracket (8) to the brush head (Fig.5).
5. Remove the water distribution pipe (9) in the hole on the brush head (10) (Fig.6).
5
7
6
8
4 5
145
460
1020
4
3
10
6
6. Bring the couplings (11), in the brush head body, to the rest position. Turn the lever in the direction
indicated by the arrow (Fig.7).
7. Lightly tip the machine back (Fig.8), block one of the rear wheels and shift the control column
backwards. Remove the brush head body from the frame.
11
7

15.4 COMPONENT POSITIONING

The basic components of the appliance are as follows:
1. Dead man's lever (Fig.1).
2. Control lever main switch (positioned under the grip of the handlebar) (Fig.1).
3. Lever for adjusting handlebar inclination (Fig.1).
4. Control lever for detergent distribution valve (Fig.1).
5. Spray kit control switch (Fig.1).
6. Brush head motor thermal trip unit (Fig.2).
7. Spray kit power socket (Fig.2).
8. The appliance's power cable (Fig.3).
9. Spray kit power cable (Fig.3).
10. Solution tank kit upper support (Fig.4).
11. Solution tank kit lower support (Fig.4).
12. Top cable tidy (Fig.5).
13. Bottom cable tidy (Fig.5).
14. Detergent solution tank (Fig.6).
15. Detergent solution cap (Fig.6).
16. Spray kit detergent solution draught tube (Fig.6).
17. Spray kit detergent solution draught filter (Fig.6).
18. Detergent solution supply tube (Fig.7).
19. Spray kit detergent solution nozzle support (Fig.7).
5 1
2
3
4
1
10
11
4
19
18
7

16. PREPARING THE APPLIANCE

16.1. HOW TO ASSEMBLE THE APPLIANCE

The appliance is supplied dismantled for packing reasons; to get it working proceed as follows:
1. Bring the couplings (1), in the brush head body, to the rest position. Turn the lever in the direction
indicated by the arrow (Fig.1).
2. Place the appliance frame above the brush head body, being careful to position the bushing (2) in
the brush head body in the slot (3) in the appliance's frame (Fig.2).
3. Secure the brush head body by tightening the couplings (1) in the brush head unit, turn the lever in
the direction of the arrow (Fig.3).
1
3
2
1
4. Position the control handlebar (4) in the rear of the frame (Fig.4).
5. Fix the handlebar to the frame using the bolts (5) supplied (Fig.5).
N.B.: The equipment needed for this operation is not included in the packaging.
9
6. Position the pump support box (6), in the spray kit, in the rear of the handlebar pipe (Fig.6).
18
8
6
7
9
3
2
12
16
13
17
5 6
1
2 3
8
15