Skullcandy STOMP MINI XT Guia De Inicio Rapido

MANUAL (EN)
FRONT PANEL
STOMP MINI
THE PORTABLE PARTY
LED BATTERY INDICATOR
POWER ON / OFF
VOLUME UP / NEXT TRACK
PLAY / PAUSE
VOLUME DOWN / PREVIOUS TRACK
LIGHT SHOW / STROBE LIGHT
STRAP HOOKS
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated within 20cm minimum distance
between the radiator & your body.
Canada warning:
- English:
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to
the following two conditions: This device may not cause interference. This device must accept
any interference, including interference that may cause undesired operation of the device.
- French:
Cet appareil contient des émetteurs/récepteurs exemptés de licence qui sont conformes aux
flux RSS exemptés de licence de Innovation, Science et développement économique Canada.
L'exploitation est soumise aux deux conditions suivantes: Cet appareil ne doit pas causer
d'interférences. Ce dispositif doit accepter toute interférence, y compris toute interférence
pouvant causer un fonctionnement indésirable du dispositif.
MODEL: 2SKSK1850 1 YEAR WARRANTY
Website: Skullcandy.com Support: 877-543-3540
2023© Skullcandy is a registered trademark Marketed and
distributed by Lifeworks technology Group LLC., New York,
NY 10018. USB Type-A™, USB Type-C™ and USB-C™ are
trademarks of USB Implementers Forum. The Bluetooth®
word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by Lifeworks
Technology Group LLC. is under license. All brands are
registered trademarks of their respective companies. *Actual
product may differ slightly from images. Made in China.
STICKER PACK
BLUETOOTH® PAIRING
TWS BUTTON
MULTI-LINK™ BUTTON
AUX 3.5MM INPUT
USB-A AUDIO IN / CHARGE OUT
USB-C CHARGE OUT
USB-C POWER INPUT
Packaging includes:
(1) Stomp Mini Speaker
™
(1) 5ft Charging Cable
(1) User Manual
FUNCTIONS
Power ON / OFF:
Press and hold the "O" button for 2s. If not connected to a Bluetooth®
device or connected but idle (not playing audio) the speaker will turn OFF
automatically after 15 min.
Play / Pause:
Press the " " button once to play or pause audio.
Volume Up:
Press "+" button to increase the volume.
Volume Down:
Press "-" button to decrease the volume.
Next Track:
Press and hold "+" button for 2s to skip track.
Previous Track:
Press and hold "-" button for 2s to go to last track.
Bluetooth Pairing:
®
Press and hold the "Bluetooth®" button for 2s to enter Bluetooth® Pairing
Mode. The speaker will disconnect from any paired device and will become
available to pair to new devices. The speaker will stay in pairing mode for 60s,
or until connected. Status LED will blink blue while in Bluetooth® Pairing Mode.
True Wireless Stereo Pairing:
Press the "TWS" button on any two Stomp™ speakers to play audio in stereo.
Status LED will be cyan to indicate Right channel and yellow to indicate Left
channel.
Exit True Wireless Stereo Mode:
Press the "TWS" button to exit TWS pairing.
SKDY Multi-link™ Transmitting:
First, connect to the Stomp™ Mini speaker by BT, AUX, or USB-A audio input
connection. Double press the "Multi-link™" button to set the speaker as
transmitting. Any receiving speaker enabled SKDY Multi-link™ will now be able
to join. Status LED will be purple.
SKDY Multi-link™ Mode Receiving:
Single press the "Multi-link™" button to set the speaker as receiving (the
speaker will automatically disconnect from any paired Bluetooth® devices).
Status LED will be green. Up to 99 receiving speakers can be connected to a
single transmitting speaker.
Check Battery Status:
The 4 LED indicators show the battery level. Press and hold "+" and "-" buttons
together for 1s to initiate a voice prompt of the battery level.
Light Show Mode
Press and hold the "Light Show" button for 2s to turn the light show ON or
OFF. Single press the "Light Show" button to cycle between different light
show modes.
Strobe Light ON/OFF
Double press the "Light Show" button to toggle the strobe light ON or OFF.
Dual-Device Connection:
You can pair two transmitting devices (mobile phones for example) to the
Stomp™ Mini speaker at the same time to DJ together. Pause the music on
the first device to play a song from the second device.
Charge Out:
While the speaker is ON, plug a USB-C™ or USB-A cable into the appropriate
port to begin charging your compatible portable device automatically.
CHARGING THE STOMP™ MINI
Use the USB-C™ cable included to connect the speaker to an appropriate
power source to begin charging. The LED indicators will show the battery is
charging. When all 4 LEDs are ON the battery is fully charged.
Warning:
1. To avoid damage to the speaker and battery, it is important to only use a
power source that matches the power requirements listed on the speaker's
rating label.
2. To avoid overheating, it's recommended not to place the speaker in direct
sunlight, especially while charging and playing music.
Battery status indication (not charging):
0-5% - speaker is OFF all 4 LEDs are OFF
5-10% - 1st LED blinks red, other LEDs are OFF
10-25% - 1st LED is ON white, other LEDs are OFF
25-50% - 1st + 2nd LEDs are ON white, other LEDs are OFF
50-75% - 1st + 2nd + 3rd LEDs are ON white, other LEDs are OFF
75-100% - All LEDs are ON white
Battery status indication (while charging):
0-25% - 1st LED blinks white, other LEDs are OFF
25-50% - 1st LED is ON white, 2nd LED is blinking.
Other LEDs are OFF
50-75% - 1st + 2nd LEDs are ON white, 3rd LED is blinking.
Other LEDs are OFF
75-99% - 1st + 2nd + 3rd LEDs are ON white, 4th LED is blinking.
Other LEDs are OFF
100% - All 4 LEDs are ON white
CONNECTION PRIORITY
AUX > USB > BT (Bluetooth®)
To play from an AUX source, simply plug in an AUX cable to the speaker and
your audio source device. It will automatically have priority over USB and BT.
To play from a USB source, plug in a USB flash drive and make sure that AUX
is disconnected. It will automatically have priority over BT (but not over AUX).
To play from BT source, connect a Bluetooth® enabled device and make sure
that AUX and USB are disconnected.
TROUBLESHOOTING
Factory Reset:
Press and hold "-" and "+" buttons at the same time for 10s to initiate factory
reset. The speaker will revert to factory settings and all previously paired devices
will be deleted. Status LED will blink between blue and red while resetting.
Low Battery:
If the speaker's battery is fully depleted, it may not turn ON immediately even
when connected to a power source. Please plug the speaker into an
appropriate power source and let it charge for at least 10 minutes before
turning it ON.
Speaker is not playing wirelessly:
If the speaker is not playing audio although it's connected to a Bluetooth™
device, it may be because of the audio connection priority. Disconnect any
AUX or USB-A cables that may be connected to the speaker and try again.
SPECIFICATIONS
Bluetooth® Version：5.3
Battery Capacity: 11.1V/3600mAh
Charging Input: DC 5V/2.2A
Playtime: 12 hours (Based on 77dBSPL(c) with light show OFF)
Charging Time: 4.5-5 hours
Operating Range: 10M
Rated Power: 40W+10W
Audio Inputs: Bluetooth®, USB-A, Aux 3.5mm
Charging Outputs: USB-C, USB-A
Battery Standby Time: 365 Days
IPX Rating: IPX7 (water immersion of 1m, for up to 30 min)
EN: SCAN FOR SUPPORT
FR: NUMÉRISER POUR OBTENIR UN SOUTIEN
ES: ESCANEAR PARA OBTENER ASISTENCIA
PL: ZESKANUJ, ABY UZYSKAĆ POMOC
SV: SKANNA FÖR SUPPORT
NL: SCANNEN VOOR ONDERSTEUNING
IT: SCANSIONE PER ASSISTENZA
DE: FÜR SUPPORT SCANNEN
BACK PANEL
Double sided pritning - Accordian Style Booklet