Publicidad
Idiomas disponibles
Idiomas disponibles
About the temperaturecontrols.
Not aft features
are on all models.
Your controls
will look like one of the foflowing:
Non-LCD models
LCDmodels
NOTE:Therefrigerator is shipped with protective film coveringthe temperature controls,If this film was not
removed during installation, removeit now,
ge.com
Thetemperature controls arepresetin thefactoryat37°F (3°¢)for the
refrigerator compartment and0_ (-18°C) f orthefreezer compartment
Allow24hoursforthetemperature t o stabilize tothepreset
recommended s ettings,
Refrigerator temperatures c anbeadjusted between 34°F and44°F
(I°C to 7°C), andthefreezer temperatures c anbe adjusted between
-6°F and+6°F(-21°C to -14°C).
Tochange the Refrigerator temperature:
LCD Models:
Access By: Horn e > RefiJgerator
Activate By: Using tile arrows to select tile desired
temi)eramre.
_4_u must press ENTERto set tile new
temperature.
Tochange the Freezer temperature:
Access By: Home > Freezer
Activate By: Using tile arrows to select tile desired
temperature.
Y)u must press ENTER to set tile new
temi)erature.
Once
tile desired
temperature
has been
set, tile display will
return
to tile NOMEscreen
and show tile set temperatures
tmderneath
the actual
temperature
display for several
seconds.
Several ac!iusnnents
may be required.
Each time
you a(!iust tile controls,
allow 24 hom_ fin" tile refl_igerator
to reach tile temperature
you have set.
Non-LCD Models:
To change tile temperature,
press and release tile WARMER
or COLDERpad. Tile SETlight will come on and tile display
will show tile set temperature.
To change
tile temperature,
tap either
tile WARMER or COLDER pad until tile desired
temperature
is displayed.
Once the desired
temperature
has been
set, tile
temperature
display will return
to tile actual refl'igerator
and fl'eezer
temperatures
alter 5 seconds.
Several
a(!justinents
ma)' be required.
Each time you a(!iust tile
controls,
allow 24 hom_ tot tile reli_igerator
to reach tile
temperature
you have set.
Thetemperature controls can display both the SETtemperature as weft
as the actual temperature in the refrigerator and freezer, Theactual
temperature may vary slightly from the SETtemperature based on
usage and operating environment
Turning the coolingsystemoff."
LCD models: Turning thecooling s ystemOFF stopscooling in boththe
freezerandrefrigerator compartments, butdoesnotshutoff electrical
powerto therefrigerator,
Non-LCD m odels: Setting eitheror bothcontrols to OFF stopscooling in
boththefreezer andrefrigerator compartments, butdoesnotshutoff
electrical p owerto therefrigerator,
LCDModels:
AccessBy:Home > Options > ]nfimnation
and Settings >
Cooling
System
Ott
To ttlrn tile cooling s}:steln back on, press tile to/ich screen
and press the ON button.
ActivateBy:Pressing ENTER.
Non-LCD Models:
%q) tile WARMER pad fin" either
tile refligerator
or tile
fl'eezer tmtil tile display shows OFF. To turn the unit back on,
press tile COLDERpad fin" either
tile refl_igerator
or fl'eezex:
Tile SETlight
will ilhmfinate
on tile side you selected.
Then
press tile COLDERpad again
(on tile side'where
tile SET
light is ilhmfinated)
and it will go to the preset
points
of 0°F
(-18°C)
for tile ti'eezer and 37°F (3°C) fin" tile reli_igerator.
When
tile unit is turned
back on, it will take up to 94 horns
to stabilize.
Performance Air Flow System
Tile Perfommnce
M>lqow System is designed
to maximize
temperature
control
in tile reti_igerator
and fl'eezer
compartments.
This unique
spedal
feature
consists
of tile
Air Tower along tile back wall of tile refligerator
and tile
Air Tunnel
on tile bottom
portion
of tile ti'eezer
rear wall.
Placing todd in ti'ont of tile lou\'e_s
on these components
will not afti_ct i)erfimnance.
Although
tile Air Tower and
tile Air Tunnel
can be removed,
doing so will attect
temperature
perfommnce.
(l_%r remowfl
instructions,
on-line,
24 horns a da_; contact
us at ge.com
or call
800.GE.CARES.
In Canada,
contact
us at geappliances.ca
or call 1.800.361.3400.)
I
,,,><,,,,,,,,,,,,,,,,,,
ii!iiiiii_i_ii{i
i
w
7,
N"
i
H
Publicidad
