Publicidad
8'x8'
4'
Ext.
8'x1 2'
Model
Base
Length
No.
of
Packages
Glory Standard (8'x
8')
244.5 cm
/
96.3"
2
Glory
+
4'
Ext.
(8'x
12')
364 cm
/
143.3"
3
Glory
+
4'
Ext. x2
(8'x
16')
483.5 cm
/
190.4"
4
Glory
+
4'
Ext. x3
(8'x
20')
603 cm
/
237.4"
5
»
During Assembly
You
may
use
Silicon
lubricant
spray
in
order to help you
slide
the panels into the profiles.
Do
not
spray
the Polycarbonate
panels.
Use
a
rubber mallet if
necessary.
All panels
with the stamped words
THIS
SIDE
OUT
must
be
facing out to create full
UV
protection.
Remove plastic sticker
as
panels are locked
in
place.
The
Auto Vent Opener
has
a
separate assembly
instruction
in its
own
package.
During assembly you will encounter the information icon,
please refer
to the
relevant assembly step for additional comments and
assistance.
This icon indicates
that the installer should
be
inside the product.
This
icon indicates
that
1
the installer should
be
outside the product.
Step
10:
Please
make
sure
the screw connection
is
made exactly
as
illustrated.
A
-
Connect the screw
in
the left hole.
B -
Connect the screw
in
the right
hole.
Step 21:
Part
7943
(Side
Louver Window)
can be
located only on one
of
the
two
central
panels.
* If
you assemble the greenhouse
with
an
extension module, the
window
can be
placed on
all panels,
except for the
last
two
end panels.
*
Note:The
selected placing will affect the next assembly
steps.
Step 26:
It
is
highly recommended to
paste
the sealing tape
at
the
bottom
edge of
panels
7903
+
7904
is
order to prevent moisture
seepage.
Step 33: Roof
window
can be
located only
on one
of
the two central roof
panels.
* If
you assemble the greenhouse
with
an
extension module, the roof windows must
be
placed on
panels only
as
specified
in
the manual.
*
Note:The
selected placing will affect the next assembly
steps.
Step 38:
Please
tighten
screws
from inside the greenhouse.
In
addition,
please
tighten
the remaining
loose screws.
Step 43:
As
mentioned
at
the
'Before Assembly' section,
prior to
fitting
the
Automatic Vent
Opener,
the power -tube
has
to
be
cooled
by
placing it
in
a
refrigerator for approximately
30
minutes.
Step
52:
Door
can be
installed
as
a
left hand door or right hand
door
as
per
your decision.
These
instructions show
a
right
hand
door
assembly.
Please
determine door opening direction.
This
decision
will affect the next assembly
steps.
Step 54:
Please
adjust the hinges height
in
accordance
with
the upper post and lower ramp
of
the door
aperture,
as
specified
in
Level
C.
Step 58: Threading parts 7888 exactly
as
specified
in
Level
C, is
very
important
in
order to
create
good
drainage.
Step 62: Anchor the shed on to
a
solid surface such
as
concrete or asphalt,
use
suitable
screws
and
plugs.
(Screws
and plugs
are
not supplied).
*Please note:
Anchoring this product to the ground
is
essential to
its
stability
and rigidity.
It
is
required to complete this
stage
in
order for your warranty to
be
valid.
/ \
Important
Recommendations
Firmly connect the greenhouse to
a
level surface
immediately after completion
of the assembly.
Tighten
all screws
once assembly
is
completed.
Screws
411
and nuts 412
are used
throughout
the assembly
process.
Screws
411
are
to
be
assembled from the outside and nuts
412
from the
inside
of the
greenhouse.
If
not specified otherwise, do not fasten
screws
and nuts
(411 &
412)
for more than
2
-3
turns.
Do
not tighten them until completion of the panels'assembly.
These
2
icons
indicate if
screw's
tightening
is
required or not.
However,
in
some steps,
temporary tightening of
a
few
screws may
be
needed
to prevent
a
profile from sliding out.
M
>1
M
o
i
Publicidad
