Sulion 075772 Manual Del Usuario página 8

Remote control
FAN
Turn on / Turn off fan
ON/OFF
Turn on water nebulizer
Water nebulizer 20"ON 40"OFF
20"
1 Speed 1
Speed 2
2
Speed 3
3
4 Speed 4
Speed 5
5
F/R Change sense or rotation
1H Timer 1h
4H Timer 4h
8H Timer 8h
LED indicator
Syncing the receiver and the remote control for fan operation
If the receiver and transmitter of this fan are properly synchronized, the fan will work. During synchronization the receiver
recognizes the signal from the transmitter, this is called the learning process.
Make sure the fan is disconnected. This is essential for the synchronization process.
Unless the synchronization process has been successful, the fan will work partially or will not work. By default, all fans have
been preconfigured at the factory and should be functional once the installation is completed and the fan is turned on.
If the remote control does not work after installation or during use, synchronization can be performed as indicated below. Note
in any case that there could be other reasons why your fan or remote control does not work:
Make sure all connections are correctly made.
Make sure that the remote control contains batteries.
Make sure that all switches (main and isolation) are on.
Instructions for synchronizing the receiver and the remote control
The control of this fan does not require synchronization with the recelver, the control is already factory-linked with its receiver;
Universal mode and Unit mode:
14
- Unit Mode:
This type of synchronization allows you to control two or more nearby fans independently, each with its remote control.
Synchronization:
The control of this fan does not require synchronization with the receiver, the control is already factory-linked with its receiver
- Universal Mode:
This type of synchronization allows you to control one or more nearby fans with the same remote control.
Synchronization:
1.-Connect the power (wall switch) of the fan or fans that you want to control, and then just within the following
15 seconds, press the key of the remote control for 5 continuous seconds.
FAN
ON/OFF
2.-A "beep" sound indicates that the connection has been executed and the equipment can function normally.
3.-Now, transmitter and receiver of the fan / s will have been synchronized. Turn off the fan / s current using the
switch or automatic and then turn it back on / s, this step is the one that closes the synchronization process.
It is not possible for a controller to forget a fan once it has been linked, if you want a fan to leave
to obey a command, another one must be linked to "overwrite it".
Remote control safety functions
Blocking protection
The remote receiver includes a function that automatically blocks motor operation, cutting current to the motor 30 seconds
after detecting an obstruction in front of the fan that prevents normal operation. When this happens, you must remove the
obstacles blocking the fan. Then, press the off button on the remote control to reset the receiver. Now you can continue to
use the fan normally.
Note: Unless you remove the obstruction blocking the fan, it will not operate correctly.
Overload prtection
If the fan's receiver detects that the motor is operating at greater than 80W (this indicates an overload), current to the motor
will be cut automatically, which will immediately stop the fan. To reset the receiver, press the off button on the remote control.
Note: If the receiver goes into protection mode again, this may indicate a motor defect. Contact the supplier immediately. The
duration of the warranty is indicated in the warranty document provided in this manual.
CIF A28763647
*
*
*
If the tank is empty, a led will light up. To fill the tank, follow
the instructions in the section "Installing the ceiling fan"
+34 916774540 Calle Verano, 51 - Polígono Industrial Las Monjas -28850 Torrejón de Ardoz - Madrid (ESPAÑA)
Rotation direction: summer and winter options
The sliding switch controls the direction, whether clockwise or counterclockwise.
Summer option/down - or left-facing position (depending on the model) - The fan runs counterclockwise. The downwards air
current creates a refreshing effect as indicated in diagram A.
Winter option/up - or right-facing position (depending on the model) - The fan runs clockwise. An ascending air current
pushes hot air away from the fan area near the ceiling, as indicated in diagram B. This allows you to use less central heating.
Note: Turn off the fan, lower the differential, and wait for it to come to a complete stop before changing the blade rotation
direction with the sliding switch.
Balancing – Wobbling problems during fan operation
If the fan body wobbles during its operation, this is not a sign of malfunctioning (even if it wobbles a few centimeters). To
reduce wobbling, you can, while the fan is off:
1. Check that all blades are properly fastened by tightening their screws.
2. Check the distance between each blade and the ceiling. Measurements to the ceiling can be carried out as shown in the
following diagram. If variations exist and you have already correctly tightened the screws, check that all blades have the
same shape. If any of them have a shape that is visibly different, this may be causing an imbalance during fan operation
If you have completed the previous steps and the wobbling has not resolved, you should apply dynamic balancing with the
kit provided, as explained below:
1. Turn the fan on to the highest speed so that the greatest amount of wobbling is produced.
2. Turn off the fan. Select a blade and place a clip on it (see diagram) halfway between the fastening and the far edge of the
blade.
ATC: 916749481 - info@sulion.es / SAT : 916749483 - sat@sulion.es
.
15
www.sulion.es