Publicidad
Idiomas disponibles
Idiomas disponibles
f)
Ensure appliance is switched OFF before connecting to mains power supply.
g) Disconnect the plug from the source and/or remove the battery pack, if detachable,
from the appliance before making any adjustments, changing accessories, or storing
appliances. Such preventive safety measures reduce the risk of starting the appliance
accidentally.
h) Store idle appliances out of the reach of children and do not allow persons unfamiliar
with the appliance or these instructions to operate the appliance. Appliances are
dangerous in the hands of untrained users.
i)
Maintain appliances and accessories. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect the appliance's
operation. If damaged, have the appliance repaired before use. Many accidents are caused
by poorly maintained appliances.
j)
Children must not play with the appliance. Cleaning and user maintenance must not be
made by children without supervision.
k) When moving from one place to another, consider the weight of the machine.
2) Electrical safety
a) Appliance plugs must match the outlet. Never modify the plug in any way. Do not use
any adapter plugs with earthed (grounded) appliances. Unmodified plugs and matching
outlets will reduce risk of electric shock.
b) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the
appliance. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
c)
Use proper extension cord. Make sure your extension cord is in good condition. When using
an extension cord, be sure to use one heavy enough to carry the current your product will draw.
An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.
d) Always check that the power supply corresponds to the voltage on the rating plate. The
electric motor is designed for a single voltage only.
e) The supply cord cannot be replaced. If the cord is damaged the appliance should be
scrapped.
3) Service
a) Have your appliance serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the appliance is maintained.
Electric Water Butt Pump Safety
WARNING: If you use an extension lead, ensure the extension connections are protected from
exposure to rain and/or water discharged by the pump.
a) The pump must always be transported, used, submerged, and stored, vertically. Carry the pump
only by the lifting handle. Never carry, lift or submerge the pump by its power cable.
b) NEVER use this pump when ambient temperatures are close to freezing.
c)
DO NOT attempt to operate the pump below the minimum water level as this will cause
permanent damage.
d) This pump must be operated exclusively on power points that are protected by an RCD with a
maximum tripping current of 30mA and a maximum delay of 40ms.
e) The electrical supply should be the same as detailed on the pump casing.
f)
DO NOT use this pump in swimming pools or ponds that are occupied. When in operation, the
area around the pump should be clear of all people and animals.
g) Ensure hands are dry whenever connecting or disconnecting the plug from the power supply.
h) When using the pump after prolonged periods of storage, first check the pump casing and
cable for any obvious signs of damage. If in doubt, consult a qualified electrician.
i)
Protect the cable and plug from exposure to oil, excessive heat, and sharp objects.
j)
Never place excessive strain on the cable as this could weaken its connections to the pump
and/or power plug.
k)
DO NOT allow children to touch the product or any of its components.
l)
This pump is designed for use in clean water environments but will discharge, in the liquid,
suspended solids no larger than 3mm diameter.
m) DO NOT use this pump with substances other than water.
n) Sand and other abrasive materials present in the liquid being pumped will cause increased
wear.
o) Where possible, avoid using the pump continuously for more than 10 minutes.
p) This pump is designed for domestic applications only, in and around the home and garden. Do
not use in a commercial or industrial environment as the pump is not designed for heavy-duty
use. It is designed for periodic on/off cycles, not for long-term continuous operation.
q) DO NOT use with liquid that has a temperature greater than 35°C.
r)
Dry running of the pump creates excessive wear and must be avoided.
s)
When not in use, protect the pump from frost damage and store in a dry place.
t)
ALWAYS observe local laws and regulations when connecting submersible pumps to the power
supply. Consult a qualified electrician when necessary.
400W Water Butt Pump
Product Familiarisation
1.
Male Quick Connector ½"
2.
Shut-Off Valve
3.
Exit Pipe
4.
Stabilising Arm
5.
Telescopic Extension Pipe
6.
Power Cable
7.
Carrying Handle
8.
Pump Unit
9.
Suction Base
10. Float Switch
11. Lower Cable Clip
12. Outlet Connector
13. Upper Cable Clip
14. Washers
Intended Use
Electric water butt pump, for pumping water from a water butt. Maximum submersible depth of 7m,
with filtration to prevent blockages, provides usable collected water at a flow rate of 41.6L/min.
Unpacking your Tools
•
Carefully unpack and inspect your new appliance. Familiarise yourself with all its features
and functions.
•
Ensure that all parts of the appliance are present and in good condition. If any parts are missing
or damaged, have such parts replaced before attempting to use this appliance.
Before Use
WARNING: Ensure the appliance is disconnected from the power supply before attaching or
changing any accessories or making any adjustments.
Pipe assembly
Note: During assembly, ensure a Washer (14) is placed between each pipe connection
(See 'Fig. II' for each position).
1. Position the Pump Unit (8) on a secure flat surface.
2. Take the Telescopic Extension Pipe (5), position the Washer, and screw the female connector
onto the threaded male Outlet Connector (12) located at the top of the Pump Unit.
3. Take the Stabilising Arm (4), position the Washer, and screw the female collar onto the threaded
male connector of the Telescopic Extension Pipe.
4. Take the Exit Pipe (3), position the Washer, and screw the female collar onto the threaded male
connector of the Stabilising Arm.
Height adjustment
•
To adjust the height of the Exit Pipe (3), unscrew the plastic collar at the top of the Telescopic
Extension Pipe (5), then re-position and tighten the collar.
Stabilising Arm adjustment
Note: The height of the Stabilising Arm (4) should correspond with the depth of the water container.
Use the Stabilising Arm to support the pump against the side of the water container.
IMPORTANT: The Stabilising Arm must not be used to hang or hold the weight of the pump
during use.
•
To adjust the height of the Stabilising Arm, unscrew the plastic collar immediately above the
arm, then re-position and tighten the collar.
Hose connection
• Attach a female hose quick connector (not included) to the garden hose, and push-fit onto the
Male Quick Connector (1).
silverlinetools.com
7
Publicidad
