Publicidad
Idiomas disponibles
Idiomas disponibles
I
NITIAL SETTING
These operations are accessible by remote control. Some may also be accessible by controls on the main unit.
Initial Setup
This section will guide you through the unit's initial setting which includes
selecting a language for your on-screen menu and auto channel scan,
which automatically scans and memorizes viewable channels.
Before you begin:
Make sure if the unit is connected to antenna or cables.
1
After making all the necessary connections, press
[POWER] to turn on the unit.
•
This operation may take a few moments.
2
Use [Cursor K / L ] to select the on-screen language
from the choices on the right side of the TV screen.
(English / Español / Français)
•
"Initial Setup" menu on step 3 will be displayed in the
selected language after you press [ENTER].
3
Use [Cursor K / L ] to select "Air" for TV channels or
"Cable" for CATV channels, then press [ENTER].
•
Scanning and memorizing of channels start
automatically.
•
When the scanning and memorizing of channels are
completed, the lowest memorized channel will be
displayed.
Initial Setup
Initial Setup
English
Select the language for setup display.
Español
Elija el idioma de ajuste.
Sélectionner langue écran config.
Français
SETUP
Select
Enter
Exit
ENTER
Initial Setup
Initial Setup
Make sure the antenna is connected to "ANT.IN" jack.
Air
Select the destination of "ANT.IN" jack.
Cable
Air
Or
Cable
ANT.IN
BACK
SETUP
Select
ENTER
Enter
Back
Exit
Initial Setup
Initial Setup
Now the system is scanning for channels,please wait.
5%
Analog channels
1ch
Digital channels
0ch
SETUP
Exit
Note:
• If you connect the cable system directly, contact the CATV
installer.
• If you press [POWER] or [SETUP] during auto channel
scan, this setting will be canceled.
• The initial auto channel scan function can be executed
for either "Air" or "Cable" only once. When you change the
connection (Air/Cable), set auto channel scan again. (Refer
to page 14.)
• You can cancel or exit the initial auto channel scan menu
by pressing [SETUP].
• If there is no signal input from the antenna terminal and
no operation for several seconds after you turn on the unit,
"Helpful Hints" appears. Follow the instructions listed on
the TV screen.
No channel is registered.
Press and hold "ENTER" key on the remote control for 3 seconds.
Contact support hotline provided on manual or back of unit.
Sin canal registrado.
Pulse durante 3 segundos la tecla "ENTER" en el control remoto.
Llame teléfono de apoyo en manual o atrás de TV.
Pas de chaîne consign.
Enfoncez "ENTER" 3 secondes sur la télécommande.
Contacter numero d'urgence dans manuel ou arrière appareil.
Main Menu
This section describes the overview of the main menu displayed when you
press [SETUP]. For more details, see the reference page for each item.
The main menu consists of the function setting items below.
Press [SETUP].
EXIT
To exit settings.
PICTURE
You can adjust the picture quality.
(Refer to "Picture Adjustment" on page 22.)
SOUND
You can adjust the sound quality.
(Refer to "Sound Adjustment" on page 23.)
CHANNEL
You can automatically scan the viewable channels and
remove the undesired channels.
(Refer to "Auto Channel Scan" on page 14.)
DETAIL
You can change the display format for closed caption,
which displays the dialogue of a TV program or other
information across the TV screen.
(Refer to "Closed Caption" on page 24.)
You can set the viewing limitations.
(Refer to "V-chip" on page 28.)
You can adjust the position, stability and clarity of the
PC screen.
(Refer to "PC Settings" on page 31.)
You can select the sound input for the HDMI1 input
jack if your unit is connected to an HDMI or DVI device.
(Refer to "HDMI Audio" on page 32.)
2-2
13
EN
Publicidad
