Descargar Imprimir esta página

Amana A8RXCGFXW Manual De Instrucciones página 14

Publicidad

Idiomas disponibles

Idiomas disponibles

Changing the Light Bulb
The light bulb is located behind the Temperature control.
IMPORTANT: Depending on your model, the light bulb in your
new refrigerator may use LED technology. If your model uses LED
lighting and the light does not illuminate when the refrigerator
door is opened, call for assistance or service. See Warranty for
phone numbers.
1. Unplug refrigerator or disconnect power.
2. Remove the light shield by squeezing in on the sides and
pulling it straight down.
3. Remove the light bulb, and then replace it with an appliance
bulb of the same size, shape and wattage.
LED Technology models only:
To replace the LED bulb with an LED bulb, order part
number W10565137 (3.6 watts).
NOTE: Some LED replacement bulbs are not
recommended for wet/damp environments. The
refrigerator and freezer compartments are considered to
be wet/damp environments. If using a brand of LED bulb
other than the recommended LED bulb, before
installation, read and follow all instructions on the LED
packaging.
To replace an LED bulb with an incandescent bulb, use
only incandescent bulbs for household appliances with a
maximum of 60 watts.
4. Replace the light shield.
5. Plug in refrigerator or reconnect power.
14
All manuals and user guides at all-guides.com
If You Choose to Leave the Refrigerator On While You're
Away:
1. Use up any perishables and freeze other items.
2. If your refrigerator has an automatic ice maker, and is
3. If you have an automatic ice maker, turn off the ice maker.
4. Empty the ice bin.
If You Choose to Turn Off the Refrigerator Before You
Leave:
1. Remove all food from the refrigerator.
2. If your refrigerator has an automatic ice maker:
3. Turn off the Temperature control(s). See "Using the Control(s)."
4. Clean refrigerator, wipe it, and dry well.
5. Tape rubber or wood blocks to the tops of both doors to prop
When you are moving your refrigerator to a new home, follow
these steps to prepare it for the move.
1. If your refrigerator has an automatic ice maker:
2. Remove all food from the refrigerator and pack all frozen food
3. Empty the ice bin.
4. Turn off the Temperature control(s). See "Using the Control(s)."
5. Unplug refrigerator.
6. Clean, wipe, and dry thoroughly.
7. Take out all removable parts, wrap them well, and tape them
8. Depending on the model, raise the front of the refrigerator so it
9. Tape the doors closed and tape the power cord to the back of
When you get to your new home, put everything back and refer to
the "Installation Instructions" section for preparation instructions.
Also, if your refrigerator has an automatic ice maker, remember to
reconnect the water supply to the refrigerator.
Vacation and Moving Care
Vacations
connected to the household water supply, turn off the water
supply to the refrigerator. Property damage can occur if the
water supply is not turned off.
NOTE: Raise the wire shutoff arm to OFF (up) position.
Turn off the water supply to the ice maker at least one day
ahead of time.
When the last load of ice drops, raise the wire shutoff arm
to the OFF (up) position.
them open far enough for air to get in. This stops odor and
mold from building up.
Moving
Turn off the water supply to the ice maker at least one day
ahead of time.
Disconnect the water line from the back of the refrigerator.
When the last load of ice drops, raise the wire shutoff arm
to the OFF (up) position.
in dry ice.
together so they don't shift and rattle during the move.
rolls more easily OR raise the leveling screws so they don't
scrape the floor. See "Adjust the Door(s)" or "Door Closing
and Door Alignment."
the refrigerator.

Publicidad

loading