Publicidad
Idiomas disponibles
Idiomas disponibles
4_WARNING:
Always wear eye
protection. Always use hearing protec-
tion. Never lean over the trimmer head.
Rocks or debris can ricochet or be
thrown into eyes and face and cause
blindness or other serious injury.
When operating
unit, stand as shown
and check for the following:
• Wear eye protection
and heavy
clothing.
• Hold trigger handle with right hand
and assist handle with left hand.
• Hold unit so that engine is below
waist level.
• Out only from your left to your right to
ensure debris is thrown away from
you. Without bending over, keep line
near and parallel to the ground and
not crowded into material being cut.
Do not run the engine at a higher speed
than necessary. The cutting line will cut
efficiently when the engine is run at less
than full throttle. At lower speeds, there
is less engine noise and vibration.
The cutting line will last longer and will
be less likely to "weld" onto the spool.
Always release the throttle trigger and
allow the engine to return to idle
speed when not cutting.
HOW TO STOP YOUR UNIT
• Release the throttle trigger.
• Move the ON/OFF switch to the OFF
position.
TRIMMER
LINE ADVANCE
The trimmer line will advance
approxi-
mately 2 inches (5 cm) each time the
bottom of the trimmer head is tapped
on the ground with the engine running
at full throttle.
The most efficient line length is the
maximum
length allowed by the line
limiter. Always keep the shield in place
when the tool is being operated.
To advance
line:
• Operate the engine at full throttle.
• Hold the trimmer head parallel to
and above the grassy area.
• Tap the bottom of the trimmer head
lightly on the ground one time. Ap-
proximately
2 inches (5 cm) of line
will be advanced
with each tap.
Always tap the trimmer head on a
grassy area. Tapping on surfaces such
as concrete or asphalt can cause ex-
cessive wear to the trimmer head.
If the line is worn down to 2 inches (5
cm) or less, more than one tap will be
required to obtain the most efficient line
length.
_I=WARNING:
Use only 0.095 inch
(2.4 ram) diameter line. Other sizes of
line will not advance
properly
and will
result in improper
cutting head func-
tion or can cause serious
injury. Do
not use other materials
such as wire,
string, rope, etc. Wire can break off
during cutting and become a danger-
ous missile that can cause serious in-
jury.
CUTTING
METHODS
A_,WARNING:
Use minimum
speed and do not crowd the line when
cutting around hard objects
(rock,
gravel, fence posts, etc.), which can
damage
the trimmer head, become
entangled
in the line, or be thrown
causing
a serious
hazard.
• The tip of the line does the cutting.
You will achieve the best perform-
ance and minimum
line wear by not
crowding
the line into the cutting
area. The right and wrong ways are
shown below=
Tip of the line
Line crowded into
does the cutting,
work area,
Right
Wrong
• The line will easily remove grass
and weeds from around walls,
fences, trees and flower beds, but it
also can cut the tender bark of trees
or shrubs and scar fences.
• For trimming
or scalping,
use less
than full throttle to increase
line life
and decrease
head wear, especially:
• During light duty cutting.
• Near objects around which the line
can wrap such as small posts,
trees or fence wire.
• For mowing or sweeping,
use full
throttle for a good clean job.
TRIMMING
- Hold the bottom of the
trimmer head about 3 inches (8 cm)
above the ground and at an angle. Al-
low only the tip of the line to make
contact
with vegetation.
Do not force
trimmer line into work area.
13
Publicidad
