Fontastic Casa+ Manual Del Usuario página 2

GB
Thank you for purchasing this Fontastic
Please read the User Manual carefully and observe the
safety instructions.
Package Contents:
• Casa+ multiple USB charging station
• 3 x Micro USB cable
• 1 x USB Type-C™ cable
• 1 x European power cord
• User Manual
Take the product out of the package and check the package contents. If any of the
above contents are missing, please put the product back in the package and return it
to your dealer.
Overview:
1. Power connector (side)
2. USB Type-C™ port
5V 2.4A
3. Smart USB ports
5V 2.4A
1
4. Fast charge port
5V 3A / 9V 2A / 12V 1.5A
5. Inductive charger (removable)
5V 1A / 9V 1.2A
6. Storage compartments
User Manual:
Connect the EU power cord included in the package to the Casa+ side power connector
and an AC outlet. Three alternating fl ashes of the blue and green LED on the inductive
charger indicate that the station is ready for operation.
IMPORTANT: When setting up, make sure that the charging station is on fi rm ground,
freely accessible, and not covered.
Charging Devices via the USB Port
Connect the device you want to charge with one of the USB cables included in the pa-
ckage and a Casa+ USB port. The charging process will start. Place the device in one
of the storage compartments. Unplug the cable from the device when it is fully charged.
NOTE: The fast charge port supports the Power Delivery, Quick Charge™,
Pump ExpressTM, AFC and FCP fast charge technologies.
Non-compatible devices will be charged in 5V (legacy) mode.
1
product!
®
6 5
2 3 4
Charging Devices via the Inductive Charger
Place the device that you want to charge on the inductive charger. Make sure that the
device to be charged with the built-in inductive receiver (usually on the battery side)
rests correctly on the inductive charger. If the inductive charger does not immediately
recognize the device to be charged, place the device on the charging station again and
reposition it if necessary until the contact between the two devices is established and
the blue LED stays on permanently.
Whether the device to be charged is positioned correctly or not can be recognized by
the charging indicator of the device that is being charged, as well as by the Casa+ blue
LED that stay on permanently. When the device is fully charged, the LED will change
from blue to green.
Using the Inductive Charger Separately
The Casa+ inductive charger can be removed and
used as a separate charger. Take out the inductive
charger by lifting it with one fi nger at the slot.
Connect one of the Micro USB cables to the inductive
charger port and the other end to a USB power source
(Fig. 1). The charger can now be used as described above.
To be able to use the fast charge feature of the wireless charger, you will need the
appropriate electronic devices with output voltages of 5V DC 2A and 9V DC 1.67A.
To insert the charger into the station, remove the cable fi rst. Place the charger in the
station so that the poles of the station and the inductive charger are on top of each
other and the charger is fi rmly seated in the station and can no longer be turned.
IMPORTANT: The inductive charger can only be used with devices that are
Qi-compatible or have a corresponding receiver pad (induction coil) inserted in them.
We assume no liability for any damage caused by incorrect operation.
If you require technical support, please contact our support team by e-mail
at service@fontastic.eu.
Technical Data :
• Input voltage: 100-240V AC
• Total output: 5V 10A, max. 50 Watts
• Output Smart USB: 5V 2.4A
• Output Type-C: 5V 2.4A
• Output Fast Charge: 3.6-12V max. 18W
• Wireless Charger output: 5V-9V max. 15W
• Protection against overvoltage, overheating and short circuit
• Dimensions: 38 mm x 142 mm x 225 mm
• Weight: 770 g
GB
Fig. 1
2