Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
MAIN MIC SECTION
28
Microphone level:
Sets the microphone level.
29
The Microphone equalizer is especifically designed for human voice
Microphone equalizer:
tone control.The control has a range of +10dB/-10dB.
30
This
ten LED segment bar depicts the level of the Mic signal. To set
Microphone level meter:
properly the signal level act upon control
(28
Level setting:
Red Leds light indicates saturation. Yellow Leds light indicates near saturation. Green Led light
indicates safe zone. Proper setting is when acting upon control
peaks for a short lapse of time.
CONNECTIONS PANEL
INPUTS SECTION
31
Channels Input connections:
Each channel is fitted with 2 RCA connector inputs. Line inputs
are for line level signal (CD Player, MD Player, MP3 Player analogue output, Cassette, etc.). Inputs
labeled Line/Phono can be fed with both types of signal according to the position of control
32
A Jack 6.3 TS (Sleeve) mono is placed at rear panel for this signal.
Main Microphone Input:
Main Mic controls at front panel will act upon this signal.
33
Submic Input:
A Jack 6.3 TS (Sleeve) mono is placed at rear panel for this signal. This signal is
directed to channel 1 by means of the input controls
34
Return connection:
A Jack 6.3 TRS (Tip, Ring, Sleeve) stereo is placed at rear panel for this
signal.
Return Level
controls at front panel will act upon this signal.
35
Turntable earth connections:
Three earth connector are available at rear panel. Fix the turntable
earth wire at these screws. If this operation is not done properly the audio signal will be parasite with
humming noise.
OUTPUTS SECTION
36
Two
Jack 6.3 TS (Sleeve) are placed at rear panel.
Balanced Master output:
are typically used to connect to the amplfier system for professional use. Specially when cable lines
are long and therefore can caught unwanted noise.
37
Connect to the amplifier system. Normally RCA output are used at
Un
Balanced Master output:
domestic setups or cable lines are short.
38
Booth
output
:
This is a second Master output normally used type for monitoring at the DJ cabin
(1 )
4
(when available). Its level is control by
important that you watch closely the amplifier connected to it to avoid saturation.
39
AJack 6.3 TRS (Tip, Ring, Sleeve) stereo is placed at rear panel for this signal.
Send connection :
Send Assign
controls at front panel will act upon this signal.
40
REC (recording) connection :
Intended for recording purposes. REC signal level is inferior to
mixer standard level to assure proper recording.
5
)
.
(28)
red leds lights only in musical
( )
(1)
and
( )
3
.
Balanced signals
. As we dont have a monitoring system for this signal it is
POWER SUPPLY SECTION
41
POWER switch:
Plug the AC adapter to the mixer and then to the Mains net. Press the ON
switch and a some LEDs will light, another press and the mixer will be OFF as well as the LEDs. Be
advised that when switching off the LED will not light off immediately due time needed for capacitors
to unload.
Attention:
Before switching on, set Master fader at "0" position.
Follow this rule:
- When starting the session, the amplifier is last to switch on.
- When finishing the session, the amplifier is first to switch off.
42
ExternalAC adapter connection:
43
Plug the USB cable from Computer to mixer .
USB connector :
44
CH-2 Line/USB selector:
MIXER ILLUMINATION
45
RCA connectors for LED lights:
2
.
the LED lights provided with the mixer for instant lighting. Turn the LED lights at your will to get the
best angle.
+ info at page 7
SETTING INPUT/OUTPUT LEVELS
Gain pot adjusts the input sensibility or so to speak the level of the input signal inside the mixer. The
input preamp (Gain) allows us voltaje level adjustment. It is paramount to set the right input level on
every channel.
Adjust the input level using the
will be correct when LED bar red LEDs only light ocasionally in short time intervals. This operation
will have to be done independently on each channel because different audio sources can have a
different output level.
Also, be aware that the LED will depict the signal level after equalizer, therefore if we increase any
of the three tone controls we will have to check the LED bar for unwanted distortion due tone control
increase.
Same thing has to be done to adjust output level for Master. When more than one channel is at Master
mix both signals will add and the overall level will increase. This fact will be monitored through the
Master LED bars
(12)
and the same channel setting procedure will have to be made using Master
fader as level control.
IMPORTANT: We have to acknowledge that a professional audio system is a serial bounded group of
professional audio devices and that saturation or other signal deterioration present in one device will
appear someway or another at the serial bounded following devices. Hence, distorted signal at mixer
output will be distorted all the way to loudspeakers.
Plug theAC adapter to the mixer at this connection.
Upon selector
(1)
position select Liner or USB Input.
Two RCA connectors are available at top of front panel, plug
HANDLING THE MIXER
Gain
pot, set it using the LED bar
(6)
as monitoring reference. Level
Publicidad
Tabla de contenido
