Cooper Lighting Solutions HALO SWL0540W Instrucciones

PACKAGING CONTENTS / CONTENU DE L'EMBALLAGE/ CONTENIDO DEL PAQUETE
SWL0540W
SWL0840W
SWL0540B
SWL0840B
ENGLISH
ITEMS REQUIRED
(Purchase separately)
• Drill with 3/16 in. drill bit
HOW IT WORKS
During the daylight hours, the integrated solar panel turns the sunlight into energy that is
stored in the rechargeable battery pack. The Solar Wedge light features a motion sensor that
turns the light ON at night when motion is detected. This light is equipped with a photocell,
which only allows the fixture to turn ON during the night time hours.
WARNINGS AND CAUTIONS
IMPORTANT: READ CAREFULLY BEFORE INSTALLING FIXTURE. FAILURE TO COMPLY WITH THESE
INSTRUCTIONS MAY RESULT IN SERIOUS BODILY INJURY, DEATH, OR PROPERTY DAMAGE.
SAVE THESE INSTRUCTIONS.
RISK OF FIRE OR INJURY
• DO NOT replace batteries.
• DO NOT puncture this battery pack. DO NOT work on this battery pack.
• DO NOT disassemble fixture. The fixture does not have any user serviceable parts.
• DO NOT dispose of this product in fire. Batteries inside this product may explode or leak.
• Lithium-Ion batteries must be disposed of in accordance with local waste ordinances and
regulations.
• Do not operate luminaire with a missing or damaged lens.
Fixture is suitable for wall and eave mount only. NOT suitable for ground mount installation
FOR BEST RESULTS
• Allow fixture to receive three full days of sunlight before turning fixture ON (AUTO Mode)
• Locate fixture in an area that will receive the maximum amount of sunlight during the
daylight hours. Panel must receive at least 3-4 hours of direct sunlight daily.
• Test your charged unit before installing.
• Locate fixture so motion moves across the detection zone (Fig.1).
• Locate fixture away from heat producing sources to prevent false triggering of a motion
event. Also be very careful not to include objects such as windows, white walls and water
in the detection zone.
Questions?/ Des questions?/ ¿Preguntas? 1-800-334-6871 ConsumerProducts@cooperlighting.com
A. Light fixture (Wedge Light)
Luminaire (luminaire en coin)
Luminario (luz en cuña)
B. Mounting Bracket
Support de montage
Soporte de montaje
Quick Release Tab
Languette à dégagement rapide
Lengüeta de liberación rápida
Fig. 1
• Locate fixture away from moving objects such as trees, large shrubs and street traffic.
• Keep solar panel clear of any objects that will block the sunlight. It will be necessary to
periodically clean the solar panel with soft wet cloth.
• During periods of several cloudy days, the battery may fall below the operating level and
will need to be recharged with sunlight.
MOUNTING YOUR FIXTURE
1. Locate area in which you would like to install your light fixture.
NOTE: For fixture to operate properly, the fixture must be located in an area that will receive
the maximum amount of sunlight and is free from obstructions.
2. Using the fixture mounting screws (C) provided, mount the snap-in mounting bracket (B)
to a solid surface by placing the screws through the centre holes of the bracket. Make
sure the tab on the bracket is pointing down. (Fig. B).
3. Rotate mode (power) knob to AUTO position.
4. Slide fixture down over the snap-in mounting bracket, making sure that the fixture
engages the guide ribs. Continue sliding down until the fixture snaps into the locking tab.
FOR PORTABLE USE
1. Press the quick release tab on the mounting bracket to remove fixture.
NOTE: Be sure to keep the fixture in the OFF position when not in use to conserve the battery.
2. Slide fixture onto mounting bracket (Fig. 2b) when finished.
Fig. (2a): Wall Mount Position
C. (2) Fixture Mounting Screws
(2) Vis de montage du luminaire
(2) Tornillos de montaje del luminario
D. (2) Wall Anchors
(2) Ancrages muraux
(2) Anclajes de pared
Fig. (2b): Sliding into the bracket