cecotec CERAMICCARE 10IN1 AIRGLAM CHAMPAGNE Manual De Instrucciones página 18

ENGLISH
1. PARTS AND COMPONENTS
Fig. 1
1. Head
2. Air speed-change button
3. Temperature-change button
4. Power button
5. Air-inlet filter cover
6. 360° rotating cable
7. Head release tab
Heads (Fig. 2)
8. Left curling barrel
9. Right curling barrel
10. Spiked straightening brush
11. Plate straightening brush
12. 50 mm round brush
13. 33 mm round brush
14. Drying head
15. 70-mm oval brush
16. Voluminising comb
17. Detangling brush
NOTE:
The graphics in this manual are schematic representations and may not exactly match the
device.
2. BEFORE USE
- This appliance is packaged in a way as to protect it during transport. Take the appliance
out of its box and remove all packaging materials. You can keep the original box and other
packaging elements in a safe place. This will help you prevent damage to the appliance
when transporting it in the future. In case the original packaging is disposed of, make sure
all packaging materials are recycled accordingly.
Make sure all parts and components are included and in good conditions. If there is any
-
piece missing or in bad conditions, contact the official Cecotec Technical Support Service
immediately.
34
CERAMICCARE 10IN1 AIRGLAM CHAMPAGNE/ CERAMICCARE 10IN1 AIRGLAM BLUE POWER RETRO 1200MAX / POWER RETRO 1200MAX CREAM&CRUSH
Box content
- CeramicCare 10in1 AirGlam Champagne / Blue
10 heads
-
Instruction manual
-
3. OPERATION
1. Wash and condition your hair.
2. Dry your hair with a towel and comb it.
3. Ensure that the mains voltage matches the voltage specified on the appliance rating label
and that the plug is earthed. Plug the appliance to a power supply.
4. Align the desired head with the air outlet and turn it to fix it to the body of the appliance.
5. Press and hold the power button to switch on the appliance: the air speed and temperature
will be set to 1 by default. If you change the settings, the device will save the last setting
for later use.
6. Air speed: repeatedly press the air speed change button to adjust the air speed. When the
speed is set to 1, the first speed LED will light up, from left to right. Press the button again
to set the speed to 2: the first and second LEDs will light up at the same time. Press the
button a third time to set the speed to 3: all three LEDs will light up at the same time. Press
the button again to return to speed setting 1.
7. Air temperature: repeatedly press the temperature change button to adjust the
temperature. When the temperature is set to 1, the first temperature LED will light up, from
left to right. Press the button again to set the temperature to 2: the first and second LEDs
will light up at the same time. Press the button a third time to set the temperature to 3: all
three LEDs will light up at the same time. Press the button again to activate the cold air, the
indicator lights will go out. Pressing it again will return to temperature setting 1.
8. Turn off the device by pressing and holding the power button and unplug it from the power
outlet when you are finished using it.
9. Automatic cleaning function: with the appliance switched off, press, and hold the
temperature change button for 5 seconds: the dryer will blow air out of the air inlet grille
for 20 seconds.
10. To remove the head, slide the release tab down, rotate the head and pull it gently to remove
it.
Using the curlers
1. With your hair at least 85% dry, place the curler on the side of the head whose hair you
wish to curl first.
2. Separate the hair into approximately 2 cm strands.
3. Select a warm or hot temperature setting.
4. Bring the end of the hair strand close to the curler: the latter will attract the hair thanks to
the Coandă effect and curl it.
CERAMICCARE 10IN1 AIRGLAM CHAMPAGNE/ CERAMICCARE 10IN1 AIRGLAM BLUE POWER RETRO 1200MAX / POWER RETRO 1200MAX CREAM&CRUSH
ENGLISH
35