Arktic 271353 Manual Del Usuario página 11

switching on again.
• No other appliances should be plugged into the same socket
as with this appliance.
• The foam blowing agent used is Cyclopentane in this appli-
ance. It is highly flammable.
• WARNING! Connect to potable water supply only.
Intended use
• This appliance is intended to be used in household and simi-
lar applications such as:
- staff kitchen areas in shops, offices and others working en-
vironment;
- farm houses;
- by clients in hotels, motels and other residential type en-
vironment;
- bed and breakfast type environment.
• The appliance is designed for making flake ice continuously.
Any other use may lead to damage of the appliance or per-
sonal injury.
• Operating the appliance for any other purpose shall be
deemed a misuse of the device. The user shall be solely liable
for improper use of the device.
Grounding installation
This appliance is classified as protection class I and must be
connected to a protective ground. Grounding reduces the risk
of electric shock by providing an escape wire for the electric
current.
This appliance is fitted with a power cord with grounding plug
or electrical connections with grounding wire. The connections
must be properly installed and grounded.
Main parts of the product
(Fig.1 on page 3)
1. Top late
2. Door
3. Ice Storage Bin
4. Power switch
5. Display panel
6. Power cord
7. Water inlet valve
8. Drainage tube
9. Feet
Remark: The content of this manual applies for all listed items
unless specified otherwise. The appearance may vary from the
shown illustrations.
Spare parts or accessories
(Fig.2 on page 4)
10. Water filter assembly
11. Water filter inlet hose 1.5m long
12. Water filter outlet hose 0.7m long
13. Filter connector x 2
14. Water drainage hose
15. Spare hose sealing washer x 2
16. Ice scoop
17. Filter holder
18. Screws x 4 for mounting filter assembly to filter holder
19. Wrench
Control panel
(Fig.3 on page 4)
1. CLEAN button to start cleaning process. Press it for 3s to
enter into clean mode
2. Running indicator
3. Cleaning in progress indicator
4. Fault indicator
a. when the fault light flashes once regularly, the condens-
er is faulty
b. when the fault light flashes twice regularly, the evapora-
tor sensor is faulty
c. when the fault light flashes three times regularly, the ice
full sensor is faulty
d. when the fault light is continuously on, it turns out water
shortage and deicing failure l
5. Ice full indicator
6. Water level is tool low indicator
Preparation before use
• Remove all protective packaging and wrapping.
• Check that the device is in good condition and with all ac-
cessories. In case of incomplete or damaged delivery, please
contact the supplier immediately. In this case, do not use the
device.
• Clean the accessories and the appliance before use (See ==>
Cleaning & Maintenance).
• Make sure the appliance is completely dry.
• Place the appliance on a horizontal, stable and heat resistant
surface that is safe against water splashes.
• Keep the packaging if you intend to store your appliance in
the future.
• Keep the user manual for future reference.
NOTE! Due to manufacturing residues, the appliance may emit
a light odor during the first few uses. This is normal and does
not indicate any defect or hazard. Make sure the appliance is
well ventilated.
Installation
ATTENTION: Any installation, maintenance and repair work
should be performed by qualified and authorized technician
only.
• Check to make sure that the appliance is undamaged or com-
plete delivery. In case of any damage or incomplete delivery,
DO NOT use the appliance and contact the supplier imme-
diately.
• Check that the accessories are included.
• Remove all packing material and protective film (if applica-
ble).
• Place the appliance on a level, steady and safe surface which
can supports the weight of the appliance together with the
flake ice produced during use.
• Avoid expose to direct sunlight or direct source of heat such
as cooker, heat oven, etc.
• Make sure that a minimum of 20 cm distance is kept around
all sides of the appliance for ventilation purposes.
• Place the appliance in such a way that the plug is easily ac-
cessible and can be quickly removed from its socket in case
of necessity.
• Set up the appliance near water supply connection.
GB
11