AEG B18FN10 Traducción Del Manual Original página 10

EN ORIGINAL INSTRUCTIONS
SPECIFIED CONDITIONS OF USE
The product is intended to drive nails in soft materials, such as
wood.
Do not use the product for any other purpose.
WARNING! Read all safety warnings, instructions,
Failure to follow all instructions listed below may result in electric
NAILER SAFETY WARNINGS
and personal injury.
If the tool is not in contact with the workpiece, the
While removing a jammed fastener, the nailer
may be accidentally activated if it is plugged in.
mechanism may be under compression and the fastener may be
forcefully discharged while attempting to free a jammed condition.
not designed for electric cable installation and may damage the
hazards.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
The product is designed for single-hand use. Do not hold the
product by the front of the magazine. Do not put hands, head, or
other parts of your body near the bottom of the magazine where the
Always ensure that the workpiece contact is fully positioned
above the workpiece. Partially positioning the workpiece contact
above the workpiece could cause the nail to completely miss the
workpiece and result in serious personal injury.
Do not drive nails near the edge of the material. The workpiece
may split, causing the nail to ricochet, injuring you or a coworker.
Be aware that the nail may follow the grain of the wood, causing it
causing injury.
Keep hands and body parts clear of the immediate work area.
Hold the workpiece with clamps when necessary to keep hands
and body out of potential harm. Make sure that the workpiece is
properly secured before pressing the fastener against the material.
The workpiece contact may cause the work material to shift
Keep face and body parts away from the back of the tool cap when
working in restricted areas. Sudden recoil can result in impact to
the body, especially when stapling into hard or dense material.
During normal use, the product will recoil immediately after driving
a fastener. This is a normal function of the product. Do not attempt
to prevent the recoil by holding the nailer against the workpiece.
time. Failure to heed this warning can result in serious personal
injury.
Do not drive fasteners on top of other fasteners or with the product
which could cause injury.
Always check the work area for hidden wiring, gas lines, and water
lines before using the product on such work area.
10
Adjust the driving depth of the nail before the actual work. It is
advisable to test the depth on a scrap workpiece to determine the
required depth for the application.
Only fasteners matching the description in the product
fasteners may lead to jamming or other malfunctions.
Always remove the battery before adjusting the depth of drive.
Do not press the trigger while adjusting the depth of drive.
Do not point the product towards yourself or anyone nearby when
adjusting the depth of drive.
Clamp the workpiece with a clamping device. Unclamped
workpieces can cause severe injury and damage.
Remove the battery pack before starting any work on the product.
ADDITIONAL BATTERY SAFETY WARNINGS
Careless
WARNING!
product damage due to a short circuit, never immerse your tool,
chemicals, and bleach or bleach-containing products, etc., can
cause a short circuit.
Do not dispose of used battery packs in the household refuse or
by burning them. AEG distributors offer to retrieve old batteries to
protect our environment.
Battery packs that have not been used for some time should be
recharged before use.
The
For an optimum lifetime, the battery packs have to be fully charged
after use.
For battery pack storage longer than 30 days:
It is
• Store the battery pack where the temperature is below 27 °C and
away from moisture.
• Store the battery packs in a 30% - 50% charged condition.
•
BATTERY PACK PROTECTION
The battery pack has overload protection that protects it from being
overloaded and helps to ensure long life.
automatically. To restart, turn the product off and then on again.
If the product does not start up again, the battery pack may have
discharged completely. Recharge the battery pack.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods
Legislation requirements.
Transportation of those batteries has to be done in accordance with
local, national, and international provisions and regulations.
• Batteries can be transported by road without further requirement.
• Commercial transport of lithium-ion batteries by third parties is
subject to Dangerous Goods regulations. Transport preparation
trained persons and the process has to be accompanied by
When transporting batteries:
• Ensure that the battery contact terminals are protected and
insulated to prevent short circuit.
• Ensure that the battery pack is secured against movement within
the packaging.
• Do not transport batteries that are cracked or leaking.
• Check with the forwarding company for further advice.
KNOW YOUR PRODUCT
See page 2.
1. Jam-clearing mechanism
2. Depth-of-drive adjustment
3. No-mar pad
4. Pusher
5. Switch trigger
6. Handle, insulated gripping surface
7. LED light button