Yellow V YVPUMP02E Manual De Usuario página 9

4 Charging
To charge the YVPUMP02E, use only the charger pro-
vided.
W
arning
Do not use the pump when the battery is being charged.
- Plug the charger into the wall socket (230 VAC). The
charger's indicator light turns green.
- Then insert the DC plug of the charging cable into the
DC socket (6) of the pump. The indicator light on the
charger turns red and the charging indicator on the
display (3) indicates the charging progress.
When the charge indicator shows four black squares and
the charger indicator light is green, the battery is fully
charged.
n
ote
It takes a while for the battery to be fully charged. Be
patient. Do not disconnect the charger until the battery
is fully charged.
5 Use
W
arning
- Do not block the air inlet at the bottom of the pump.
Make sure the air inlet is free at all times.
- If the air hose is damaged, do not use the pump and
replace the hose immediately.
- Do not disconnect the air hose during inflation to avoid
injury due to high pressure.
- Do not run the pump for more than 15 minutes at a
time; this can lead to overheating of the motor and
internal damage. After 15 minutes, give the pump at
least half an hour's rest to cool down.
- If the pump has operated continuously for more than
15 minutes, the warning symbol (5) flashes. If the
pump has operated continuously for more than 20
minutes, the warning symbol (5) remains on.
- Avoid exposure to intense sunlight.
- This product should not be exposed to rain or im-
mersed in water.
- Stay near the pump while inflating.
- Do not point the air outlet at body parts.
- If parts of the pump are damaged, do not use it and
contact a professional for repair.
5 .1 Inflating
The pump features two modes. Initially, it delivers low
pressure and high volume. When the pressure reaches
1 PSI, the pump automatically switches to high pressure
with a lower volume.
9
Next level leisure
n
ote
Use the built-in lithium battery as the power supply or
connect the external 12 VDC car power supply (5). If the
built-in battery is chosen, make sure it is fully charged.
- Choose the matching air nozzle and silicone gasket
from the included accessories.
- Connect the air hose
with the nut side to the
air outlet (8) and tight-
en it clockwise.
- Connect the other end
of the air hose to your
inflatable.
- Long press the power button (3) to turn on the pump's
screen. The screen lights up, the pump is ready for use.
n
ote
If the pump is not started after the screen is switched
on, the screen will automatically switch off after 30 sec-
onds. Long press the on/off key (3) to switch the screen
on again.
- Select one of the pre-programmed pressures (12, 15
or 20 PSI) by pressing the minus button (2) or plus
button (4).
To set the pressure manually, press the minus button
(2) or plus button (4) until the settings symbol (5)
and the set pressure (1) start flashing. Now set the
desired pressure using the minus button (2) or plus
button (4). Release the button. The set value flashes
three times for confirmation.
- Briefly press the on/off button (3) to switch on the
pump motor.
When the set value is reached, the pump automatically
stops and the inflation of your inflatable boat is complete.
5 .2 Deflating
n
ote
Use the built-in lithium battery as the power supply or
connect the external 12 VDC car power supply (5). If the
built-in battery is chosen, make sure it is fully charged.
- Choose the matching air nozzle and silicone gasket
from the included accessories.
- Connect the air hose
with the nut side to
air inlet (7) and tighten
clockwise.
- Connect the other end
of the air hose to your
inflatable.
EN