AQUAPHOR PRO 1 Manual De Instrucciones página 3

.......................................................................................................................................................................
• The resource of replacement cartridges is set for water
filtration that meets the current sanitary standards. The
service life of the replacement cartridges may be reduced
if the water being treated does not meet the current
sanitary standards.
• This accounts for multiple regeneration of the Pro H
cartridge.
The replacement filter cartridges shall be replaced upon
expiration of the service life.
Using the water filter beyond its service life term may result
in harm to the health or property of the consumer or third
persons and shall be avoided.
The service life of the membrane cartridge directly depends
on the water treatment unit performance.
Please replace the filter cartridges that have exhausted their
service life in a timely manner.
REPLACEMENT OF FILTERING
CARTRIDGES PRO 1, PRO 2, PRO H,
PRO 50, PRO 100, PRO HF, PRO UF,
PRO M, PRO HFM:
• cut off water before the water purifier and open the
faucet for pure water for depressurization;
• push firmly and hold locking pushbutton on the cover
of the water purifier, turn the used-up cartridge counter
clockwise (fig. 1);
• remove shrink film from the new cartridge;
• insert the new cartridge firmly upwards into the collector,
and slightly pushing, turn the cartridge clockwise until the
click (fig. 2);
Pay attention to the order in which the cartridges are fitted.
• turn on the water supply and make sure that the water
purifier is leak tight;
• adjust water consumption according to the recommended
filtration rate;
• infiltrate water through the water purifier within 10
minutes;
• turn off the faucet for pure water and leave the water
purifier for 10 minutes;
• infiltrate water once more through the water purifier
within 5 minutes;
• turn off the faucet for pure water;
• check leak tightness of all connections.
FOR CARTRIDGE REPLACEMENT PRO H:
• remove shrink film from the new cartridge Pro H;
• insert the new cartridge Pro H firmly upwards into the
collector, and slightly pushing turn the cartridge clockwise
until you hear click (fig. 2);
push
turn
FIG. 1
turn
• infiltrate water through the water purifier within 10
minutes;
• turn off the faucet for pure water;
• check leak tightness of all connections.
.................................................................................................................
ATTENTION! If you use water purifier with the cartridge Pro H,
during replacement of the cartridges while preparing the
water purifier for operation (rinsing), use the plug (it is in the
set of the water purifier) instead of the cartridge Pro H.
ATTENTION! When flushing water purifier with the plug in
place, control the flow rate in order to prevent any leakage.
.................................................................................................................
Timely replace cartridges of your water purifier.
Traces of carbon in the water at rinsing stage is not a sign of
a defective product. The filter contains activated carbon from
coconut shells, so carbon dust may form during transporta-
tion. Carbon is non-toxic and meets food requirements.
REGENERATION
OF THE CARTRIDGE PRO H:
Regeneration intervals depend on hardness of influent water.
Application of the softening replacement cartridge Pro H
with ion-exchange resin is effective for water with medium or
average hardness.
If the water hardness exceeds 5 mEq/l, it is recommended to
use reverse osmosis system Aquaphor OSMO Pro.
FOR REGENERATION OF THE REPLACEMENT
CARTRIDGE PRO H:
• carry out the first two points of Clause REPLACEMENT OF
FILTERING CARTRIDGES PRO 1, PRO 2, PRO H, PRO 50,
PRO 100, PRO HF, PRO UF, PRO M, PRO HFM.
ASSEMBLE AND CONNECT TO THE CARTRIDGE PRO H
REGENERATION ADAPTER (IT IS IN THE SET OF THE
WATER PURIFIER OR SHOULD BE PURCHASED
SEPARATELY) (FIG. 3):
• install the gasket (3) into the
nut (2);
• firmly put the nut (2) with the
gasket (3) on the adapter (1);
• put the plastic tube (4) on
the adapter flange (1);
• tightly insert the adapter (1)
into the cartridge (6);
• screw a standard clean
plastic bottle (5) to the nut
(2) with the cut off bottom
(like a funnel);
• prepare 2–2.5 liters of
saturated solution in the
boiled water (approx. 300
g/l) of table salt (use non-
iodized salt);
• install the cartridge with the
joint plastic bottle vertically
(for example, into a jar). Put
the plastic tube into the sink;
• pour 2–2.5 liters of salt solution through the cartridge.
FIG. 2
Pay attention that no salt sediments get into the cartridge.
EN
5
4
3
2
1
6
FIG. 3
3