Publicidad
FLOW TIME ADJUSTMENT
Adjustment Levels
The flow time is programmable on site. If necessary, the default flow time of 8 seconds can be adjusted to any value between 1 to 60
seconds. The touch adjustment mechanism is composed of 3 adjustment levels for changing the flow time. An indicator light (LED) will
guide you from one level to the other.
The following table shows the number of steps in each level, the duration of each step and how to recognize what adjusting level you are in.
No. of steps
Seconds to be increased by touching once
Adjustment level indicator
The following examples show how to manage the adjustment levels:
Example 1: You wish to adjust the flow time to 20 seconds.
At level 1, perform 3 steps of 1 second (you will get 3 seconds). Total: 3 seconds. Go to level 2 and perform 1 step of 2 seconds (you will
get 2 seconds). Total: 5 seconds. Go to level 3 and perform 1 step of 15 seconds (you will get 15 seconds). Total: 20 seconds.
Example 2: You wish to adjust the flow time to 45 seconds.
At level 1, perform 1 step of 1 second (you will get 1 second). Total: 1 second. Go to level 2 and perform 7 steps of 2 seconds (you will get
14 seconds). Total: 15 seconds. Go to level 3 and perform 2 steps of 15 seconds (you will get 30 seconds). Total: 45 seconds.
Example 3: You wish to adjust the flow time to 60 seconds.
At level 1, perform 10 steps of 1 second (you will get 10 seconds). Total: 10 seconds. Go to level 2 and perform 10 steps of 2 seconds
(you will get 20 seconds). Total: 30 seconds. Go to level 3 and perform 2 steps of 15 seconds (you will get 30 seconds). Total: 60 seconds.
How to Adjust the Flow Time
1. Open the piezo cap using the provided 2 mm Allen key.
2. Disconnect the power supply (batteries or transformer).
3. Wait ten seconds.
4. Reconnect the power supply.
5. The indicator light (LED) on the back of the piezo cap will start blinking. After a few blinks, the LED will give a steady red light. Touch the
piezo cap when the steady red light is still on to enter into the adjusting mode. When done correctly, the light will stop blinking.
NOTE: If you do not press at the indicated area, the previous adjustment will remain.
6. By touching the piezo cap, the new flow time will be programmed. In adjusting mode level 1, each touch increases the flow time by one
second with a maximum of 10 seconds. You will see the LED blinking every time that a new step is performed.
7. If your desired flow time is within 10 seconds, no other adjusting levels are needed and you can stop pressing the piezo cap. The LED
will blink 2 times then 3 times and after 4 times, you will leave the adjusting mode. The faucet is now adjusted to the desired flow time.
8. If you need to perform steps at adjusting level 2, wait until after you see the LED blink twice, and then perform the needed number of
steps (with a maximum of 10 steps of 2 seconds).
If you do not need more levels, stop pressing. The indicator light will blink 3 times and after 4 times, you will leave the adjusting mode.
The faucet is now adjusted to the desired flow time.
9. If you need to perform steps at adjusting level 3, wait after you see the LED blink 3 times and then perform the needed number of steps
(with a maximum of 2 steps of 15 seconds).
10. To leave the adjusting mode, wait until the LED blinks 4 times. The faucet is adjusted to the desired flow time.
Level 1
Level 2
10 steps
10 steps
2 seconds
1 second
After entering
Indicator
into adjusting
light blinks
mode level 1
twice
is reached
www. specselect.com
Page 6
Level 3
Out of Adjusting Mode
2 steps
15 seconds
Indicator
Indicator light blinks 4 times
light blinks
3 times
204457 Rev. A
Publicidad
