Publicidad
Idiomas disponibles
Idiomas disponibles
4) Remote control cannot be used
1. Test method: Turn on the camera of the mobile phone and align the light of the remote
control, then press the button of the remote control to see if the phone will light up. If it is not
lit, there will be no power. Replace the battery; If it is lit, there is electricity, which proves that
there is no problem with the remote control.
5) Settings can not be saved ( no memory )
1. The yellow line and the red line are connected together (separate yellow to positive,
red to key control).
2. Yellow and red are reversed (just change position).
6) Car audio with Bluetooth but it can't work
Operation steps: turn on the unit, use the phone Bluetooth search, search for
device, then click the connection, after connecting, you can answer the phone or
Bluetooth to play the song.
7) The product smoke has proved that the internal circuit has been
burned. Change the insurance FUSE can not solve the problem.
-- In this case, the unit needs to be repaired.
8) How to adjust the sound, where is the equalizer set, the sound can not
be adjusted
1. Adjust the sound: please turn the volume to adjust.
2. Equalizer settings: In general, press the volume knob to display the equalizer SEL, and
rotate the volume button to adjust each sound effect.
3. The sound cannot be adjusted:
a. Please reset the unit or unplug the power cord and plug it in.
b. The Volume knob is broken, and the knob can be replaced.
9) No display of reversing video
1. Connect the wrong line or less wiring. Camera connection method:
a> The first step is to find accessories (accessory: one camera + one power cord +one video
cable). b> The second step is to find the port of the wiring.
First find the reverse control line on the power line of the unit. The control line is a pink line
or brown line, connect this line to the positive pole of 12V and the screen will turn blue.
And then find the back of the unit the CAME video input interface, find the positive and
negative of the backup light.
The third step is connect: there are two sockets on the camera,
the red socket is connected to the power cable, the yellow is inserted into the video cable, the
red wire of the power cable and the wire of the video cable are screwed together on the
positive pole of the reverse lamp, and the black wire of the power cable is not used,
connected, the other end of the video cable is connected to the CAME video input interface on
ENGLISH
9
the back of the unit. The red line coming out of the video line is connected to the reversing
control line of the power line.
2. The camera is broken. If the lamp that is properly wired to the camera is not lit, it will be
broken and replaced with a new one.
10) USB flash disk can not be played, the card slot does not enter the card?
Format the USB flash disk, and the file system is selected as: FAT32, re-download on or two
songs and try again. If it still doesn't work, please replace the USB flash drive.
--- The card slot does not enter the card:
Check whether the memory card is inserted, the plug is broken.
11) FM does not receive the radio station
1. The antenna plug is not fully inserted, the antenna is disconnect or the line is disconnect.
2. Search channel, hold AMS does not let go for 2 seconds The unit will automatically search
or press the up and down button to perform a channel search. Can't solve the above 2
points, Please unplug the antenna plug and find a screwdriver or a metal strip to insert it
instead of the antenna.
12) There is no sound right after installation
1. Check if the speaker cable is short-circuited and connected. Please reconnect if you have
any short circuit.
2. Check how many speaker cables according to the original speaker cable if there are only
2 speaker cables to prove that the original car line does not match our unit, you need to
re-route the original car line. One speaker must lead to 2 speaker wires. 2 speakers
must be have 4 speaker cables to available.
13) There is no sound after a while
-- Disconnect all the speaker cable from the unit (do not remove them), and then find an
external speaker to receive the gray and purple of the tail line of the unit.
Green any group, and then try to see if there is any sound. If there is a sound, it is proved
that the car's speaker line is short-circuited with iron or the speaker is damaged. If there is
no sound, the unit is broken.
Tips: If the device is updated, the functions are subject to change without prior notice.
10
ENGLISH
Publicidad
