Ermenrich Zing WT60 Voltage Tester
EN
Getting started
• Open the battery compartment cover (7) and insert 2 AAA batteries according to the correct polarity. Close the cover.
• Press and hold (5) for 3 seconds to turn the device on/off.
Testing
Put the sensor (1) up to a known AC power source to test the device. If it emits a sound and the LED indicator (3) flashes, the device can be
used.
Usage
Put the sensor (1) up to a cable, a wire or a socket. The device will beep fast and the LCD display (4) will be red if the signal is strong. This
means that the device has detected a live line. The device will beep slow and the LCD display (4) will be green if the signal is weak. This
means that the device has detected a neutral or weak line.
A low-pitched sound will be emitted and the LED indicator (3) will blink when it detects AC voltage in the 12–48V range. A high-pitched
sound will be emitted and the LED indicator (3) will light up when it detects AC voltage in the 48–1000V range.
!
Random beeps and flashes may occur due to detection of static charges.
Sensitivity setting
Press (6) to switch between the low and high sensitivity modes (the default mode is low sensitivity).
Flashlight
Press and hold (6) for 3 seconds to turn the flashlight (2) on/off.
!
If the light is dim, please replace the batteries.
Non-contact phase sequence detection
Press (6) until the
P
symbol will appear on the display.
A
The
symbol will appear. Put the sensor (1) up to the first phase line and wait until the device will beep and LED indicator (3) will blink.
B
The
symbol will appear. Put the sensor (1) up to the second phase line and wait until the device will beep and LED indicator (3) will blink.
C
The
symbol will appear. Put the sensor (1) up to the third phase line and wait until the device will beep long and LED indicator (3) will
blink. The detection results will appear on the LCD display (4). The
symbol indicates clockwise phase rotation (direct).
Low battery indicator
When the voltage is below 2.3V, the device will display low battery icon. Immediately replace the batteries after it happens.
Specifications
Voltage detection measurement range
Voltage range of phase detection
Frequency range
Sound signal
Light signal
Device auto-off
Operating temperature range
Power supply
Safety rating
The manufacturer reserves the right to make changes to the product range and specifications without prior notice.
Care and maintenance
Always test the device prior to using it. Do not touch any bare conductor with your hand or skin. Do not use the device if it is damaged or
does not operate properly. Use extreme caution when voltages exceeding the true RMS value of 30V AC. Such voltages may result in electric
shock. The measured voltage must not exceed the nominal value specified in the technical data sheet. Do not use the device in potentially
explosive rooms. Do not use the device in aggressive atmosphere. Do not open the device. Replace the battery as soon as the low battery
indicator lights up. Follow local and national safety regulations when working in hazardous locations. Protect the device from sudden impact
and excessive mechanical force. Never attempt to operate a damaged device or a device with damaged electrical parts! Only use accessories
and spare parts for this device that comply with the technical specifications. If a part of the device or battery is swallowed, seek medical
attention immediately. Keep away from children.
Battery safety instructions
Always purchase the correct size and grade of battery most suitable for the intended use. Always replace the whole set of batteries at one
time; taking care not to mix old and new ones, or batteries of different types. Clean the battery contacts and also those of the device prior
to battery installation. Make sure the batteries are installed correctly with regard to polarity (+ and –). Remove batteries from equipment
symbol indicates counterclockwise phase rotation (inverse). The
0...+40°C (operating), −10...+50°C (storage) / +32...+104°F (operating), +14...+122°F (storage)
EN61010-1-2-030; EN61326-1; CAT III, 1000V
high sensitivity: 12–1000V AC
low sensitivity: 48–1000V AC
90–400V AC
50/60Hz
+
+
300 seconds
2pcs alkaline AAA batteries (1.5V)
3