Publicidad
Idiomas disponibles
Idiomas disponibles
Attaching High Pressure Hose (Fig. C)
CAUTION: NEVER PULL WATER SUPPLY HOSE TO
MOVE pressure washer. This could damage hose and/
or pump inlet.
nOTE: Uncoil the high pressure hose
to prevent kinks.
nOTE: Avoid cross threading when installing the hose. Cross
threading will cause leaks.
1. To connect the high pressure hose
handle grip
5
, thread the hose collar
inlet coupler
10
.
Attaching Quick Connect Nozzles (Fig. D)
DANGER: Risk of fluid injection. Do not direct
discharge stream toward persons, unprotected skin,
eyes or any pets or animals. Serious injury will occur.
WARNING: Flying objects could cause risk of serious
injury. DO NOT attempt to change nozzles while
pressure washer is running. Turn pressure washer unit
OFF before changing nozzles.
1. To connect a nozzle
21
120° curved rod
20
, pull the quick connect collar
toward the telescoping wand
appropriate nozzle
21
2. Release the quick connect collar to lock the nozzle into place.
3. Give the nozzle a firm tug after the quick connect collar
has locked into place to ensure the nozzle is locked
into place.
nOTE: The nozzles listed below might not be included with your
pressure washer but are available for purchase at an additional cost.
Common Spray Nozzles
15 ° Orange Nozzle
25 ° Green Nozzle
40 ° White Nozzle
Black Turbo Nozzle
Adjusting the Telescoping Wand Length
(Fig. A, E)
WARNING: Always check to make sure that the
pole adjust levers are completely locked and
that the telescoping pole does not move before
using or transporting the telescoping wand. Not
locking the pole adjust lever could result in the
telescoping pole unexpectedly moving, creating
a hazardous condition. Periodically check
the pole adjust levers to ensure that they are
completely locked.
The telescoping wand
1
at any position in between.
1. Unlock the pole adjust lever(s)
2. With one hand firmly grasping the telescoping
assembly
24
, slide the telescoping pole(s)
22
before installation
22
to the
23
onto the
to the 30° curved rod
1
and insert the
.
Common Applications
For brick or masonry.
For vinyl siding.
For automotive washing.
For abrasive cleaning.
can be used retracted, extended, or
7
as shown in Fig. E.
8
the other hand as shown in Fig. E. This will reveal the
stored telescoping pole(s)
3. Ensure the telescoping wand hose
the telescoping pole to prevent kinks.
4. Once you have reached the desired telescoping length,
lock the pole adjust lever(s)
pole in place. Ensure the telescoping pole(s)
secured into position before use.
Adjusting the Harness (Fig. F—I)
1. Place the harness
2. Adjust the straps
3. Wrap the waist belt
the buckle
loosen the waist belt
4. Connect the harness buckle
on the telescoping wand
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
19
or
power source before making any adjustments or
24
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
SPECIFICATIONS
Connection
Maximum Pressure
Maximum Flow Rate
Maximum Water Temperature
Telescoping Length
Proper Hand Position (Fig. A, J)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the telescoping
handle grip
nOTE: Always wear the harness
buckle
13
telescoping wand
Preparing Surface for Cleaning
CAUTION: Before operation:
•
Remove objects from the area which could create a
hazard such as children's toys or outdoor furniture.
•
Ensure that all doors and windows are closed tight.
Protect all plants and trees in the adjacent area with a
drop cloth ensuring that they will not be harmed by
any overspray.
•
Pre-rinse cleaning area with fresh water.
out with
•
Always test detergent in an inconspicuous area before use.
8
.
7
to secure the telescoping
11
over your shoulders.
14
as desired.
15
around your waist and fasten
12
. Adjust the waist belt straps to tighten or
15
as desired.
13
1
.
1/4" Quick connect
Up to 3,000 psi
Up to 1.7 gpm
140 °F (60 °C)
5.2-18 feet (1.6-5.5 meters)
5
and the other hand on the spray handle
11
connected to the wand buckle
1
.
English
6
slides freely into
8
are
to the wand buckle
16
2
.
and have the harness
16
on the
5
Publicidad
