Publicidad
Idiomas disponibles
Idiomas disponibles
Additional Safety Information
WARNING: Never modify the power tool or any part of
it. Damage or personal injury could result.
WARNING: ALWAYS use safety glasses. Everyday
eyeglasses are NOT safety glasses. Also use face or
dust mask if cutting operation is dusty. ALWAYS WEAR
CERTIFIED SAFETY EQUIPMENT:
•
ANSI Z87.1 eye protection (CAN/CSA Z94.3),
•
ANSI S12.6 (S3.19) hearing protection,
•
NIOSH/OSHA/MSHA respiratory protection.
WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction activities
contains chemicals known to the State of California to
cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
•
lead from lead‑based paints,
•
crystalline silica from bricks and cement and other
masonry products, and
•
arsenic and chromium from
chemically‑treated lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to filter
out microscopic particles.
Wear protective clothing and wash exposed areas
•
with soap and water. Allowing dust to get into your
mouth, eyes, or lay on the skin may promote absorption of
harmful chemicals. Direct particles away from face and body.
•
Use clamps or other practical ways to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body is unstable and may
lead to loss of control and injury.
Air vents often cover moving parts and should be
•
avoided. Loose clothes, jewelry or long hair can be caught
in moving parts.
CAUTION: When not in use, place tool on its
side on a stable surface where it will not cause
a tripping or falling hazard. Some tools with large
battery packs will stand upright on the battery pack
but may be easily knocked over.
WARNING: Always wear proper personal hearing
protection that conforms to ANSI S12.6 (S3.19)
during use. Under some conditions and duration
of use, noise from this product may contribute to
hearing loss.
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ......................... volts
Hz ....................... hertz
min ..................... minutes
or DC ...... direct current
...................... Class I Construction
(grounded)
.../min .............. per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
OPM .................... oscillations per
minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM .................... strokes per minute
A ......................... amperes
W ........................ watts
Wh ...................... watt hours
Ah ....................... amp hours
or AC ........... alternating current
or AC/DC .... alternating or direct
current
...................... Class II Construction
(double insulated)
n o ....................... no load speed
n ......................... rated speed
PSI....................... pounds per square
inch
The RBRC® Seal
Please take your BLACK+DECKER
with a spent battery to an authorized
BLACK+DECKER service center or to
your local retailer for recycling. In some
areas, it is illegal to place spent battery packs in the trash.
You may also contact your local recycling center for
information on where to drop off the spent battery pack. Do
not place in curbside recycling. For more information visit
www.call2recycle.org. or call the toll free number in the
RBRC® Seal.
RBRC® is a registered trademark of Call 2 Recycle, Inc.
BATTERY AND CHARGER
The battery is not fully charged out of the carton. Before using
the charger to charge the battery, read the safety instructions
below and then follow charging procedures outlined.
Only for use with S010QU1400040 chargers.
READ ALL INSTRUCTIONS
Important Safety Instructions for All
Integral Battery Tools
WARNING: Read all safety warnings, instructions,
and cautionary markings for the battery, charger
and product. Failure to follow the warnings and
instructions may result in electric shock, fire and/
or serious injury.
NEVER force a charger cord plug into the tool.
•
•
DO NOT modify a charger cord plug of a
non‑compatible charger in any way to fit into the
tool as the battery may rupture causing serious
personal injury.
DO NOT charge or use the battery in explosive
•
atmospheres, such as in the presence of flammable
liquids, gases or dust. Inserting or removing the plug
from the tool may ignite the dust or fumes.
•
ONLY CHARGE the tool with provided charger
DO NOT splash or immerse in water or other liquids.
•
•
DO NOT allow water or any liquid to enter tool.
DO NOT store or use the tool in locations where the
•
temperature may reach or exceed 104 °F (40 °C) (such
as outside sheds or metal buildings in summer). For
English
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation
do not stare into
the light
..................... wear respiratory
protection
..................... wear eye protection
..................... wear hearing
protection
..................... read all
documentation
..................... do not expose to
rain
5
Publicidad
