Nozzle Cleaning; Optional Accessories - Makita 1911B Manual De Instrucciones

Connecting a vacuum cleaner (Fig. 6 & 7)
NOTE:
• In some countries, the nozzle may not be included in
the tool package as standard accessory.
For tool with nozzle
Connect a hose of the vacuum cleaner to the nozzle.
For tool without nozzle
1. Remove the chip cover from the tool.
2. Install the nozzle on the tool using the screws.
3. Connect a hose of the vacuum cleaner to the nozzle.

Nozzle cleaning

Clean the nozzle regularly.
Use a compressed air to clean the clogged nozzle.
OPERATION
WARNING:
• To reduce the risk of injury to persons, do not oper-
ate without nozzle or chip cover in place.
Planing operation (Fig. 8)
First, rest the tool front base flat upon the workpiece sur-
face without the blades making any contact. Switch on
and wait until the blades attain full speed. Then move the
tool gently forward. Apply pressure on the front of tool at
the start of planing, and at the back at the end of planing.
Planing will be easier if you incline the workpiece in sta-
tionary fashion, so that you can plane somewhat downhill.
The speed and depth of cut determine the kind of finish.
The power planer keeps cutting at a speed that will not
result in jamming by chips. For rough cutting, the depth of
cut can be increased, while for a good finish you should
reduce the depth of cut and advance the tool more
slowly.
Chamfering (Fig. 9 & 10)
To make a cut as shown in Fig. 9, align the "V" groove in
the front base with the edge of the workpiece and plane it
as shown in the Fig. 10.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
To maintain product SAFETY and RELIABILITY, repairs,
carbon brush inspection and replacement, any other
maintenance or adjustment should be performed by
Makita Authorized or Factory Service Centers, always
using Makita replacement parts.
Sharpening the planer blades (Fig. 11, 12 & 13)
Always keep your blades sharp for the best performance
possible. Use the sharpening holder to remove nicks and
produce a fine edge.
First, loosen the two wing nuts on the holder and insert
the blades (A) and (B), so that they contact the sides (C)
and (D). Then tighten the wing nuts.
Immerse the dressing stone in water for 2 or 3 minutes
before sharpening. Hold the holder so that the both
blades contact the dressing stone for simultaneous
sharpening at the same angle.
6

OPTIONAL ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• High-speed steel Planer blade
• Mini planer blade
• Sharpening holder assembly
• Blade gauge
• Guide rule
• Extension guide set
• Dressing stone
• Nozzle assembly
• Dust bag assembly
• Joint
• Socket wrench
NOTE:
• Some items in the list may be included in the tool pack-
age as standard accessories. They may differ from
country to country.
Noise
The typical A-weighted noise level determined according
to EN62841-2-14:
Sound pressure level (L
Sound power level (L
Uncertainty (K): 3 dB (A)
NOTE:
• The declared noise emission value(s) has been mea-
sured in accordance with a standard test method and
may be used for comparing one tool with another.
• The declared noise emission value(s) may also be
used in a preliminary assessment of exposure.
WARNING:
• Wear ear protection.
• The noise emission during actual use of the power
tool can differ from the declared value(s) depend-
ing on the ways in which the tool is used especially
what kind of workpiece is processed.
• Be sure to identify safety measures to protect the
operator that are based on an estimation of expo-
sure in the actual conditions of use (taking account
of all parts of the operating cycle such as the times
when the tool is switched off and when it is running
idle in addition to the trigger time).
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN62841-2-14:
Work mode: planing softwood
Vibration emission (a
Uncertainty (K): 1.5 m/s
ENG102-3
): 86 dB (A)
pA
): 97 dB (A)
WA
ENG907-1
ENG222-2
2
): 3.5 m/s
h
2