Assembling The Stand - Milwaukee 48-08-0561 Manual Del Operador

SPECIFIC SAFETY RULES
TABLE SAW STAND
Read all safety warnings and all
WARNING
instructions provided with the ta-
ble saw stand and the table saw to be mounted.
Failure to follow the warnings and instructions may
result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
• Disconnect the battery pack from the table saw
before making any adjustments or changing
accessories. Accidental starting of the power tool
is a cause of some accidents.
• Properly assemble the table saw stand before
mounting the tool. Proper assembly is important
to prevent risk of collapse.
• Securely fasten the table saw to the table saw
stand before use. Table saw shifting on the table
saw stand can cause loss of control.
• Place the table saw stand on a solid, flat and level
surface. If the table saw stand can shift or rock, the
table saw or workpiece cannot be safely controlled.
• Do not overload the table saw stand or use as
ladder or scaffolding. Overloading or standing on
the table saw stand causes the stand to be "top-
heavy" and likely to tip over.
• Use only with MILWAUKEE Table Saws 2736-20,
and mount securely, according to these instruc-
tions. Improperly installed Table Saws can cause
injury or property damage.
• Avoid dangerous environments. Use your tool stand
on flat, level, dry, and hard surfaces only.
• Keep work area clean and well lit. Cluttered, dark
work areas invite accidents.
• The table saw stand weight limit is 180 lb (82 kg).
If more than 180 lbs is placed on the table saw stand it
may be damaged and may cause personal injury.
• Maintain control. Keep proper footing and balance at
all times.
• Maintain table saw stand carefully. Keep table saw
stand dry, clean and free from oil and grease. Follow
instructions for changing accessories. Periodically
inspect table saw stand for damage and wear.
• Maintain labels. These carry important information. If
unreadable or missing, contact a MILWAUKEE service
facility for a free replacement.
• Keep bystanders away. Children and bystanders
should be kept at a safe distance from the work area
to avoid distracting the operator.
• To reduce the risk of injury, always wear eye pro-
tection.
• Fingers can be pinched between the legs of the
table saw stand. To reduce the risk of injury, keep
your fingers out of the areas where the legs will
fold.
• Always use common sense and be cautious
when using tools. It is not possible to anticipate
every situation that could result in a dangerous out-
come. Do not use this tool if you do not understand
these operating instructions or you feel the work is
beyond your capability; contact Milwaukee Tool or
a trained professional for additional information or
training.
ASSEMBLY
Properly assemble the table saw
WARNING
stand before mounting the tool.
Proper assembly is important to ensure stability.
Legs must match with corresponding number
indicators on the stand.

Assembling the Stand

Indicators
1
3
1
Short
Bolt & Nut
Adjustable
Foot & Nut
1. Remove all packaging and zip ties.
2. Insert the legs into the frame according to the in-
dicator stickers. Mismatched leg/frame assembly
will cause the frame to wobble.
3. Insert a small bolt through the frame/legs assembly
and thread on the nut. Use a 6 mm hex wrench
and an adjustable (or 17 mm open end) wrench
to securely tighten.
4. Insert the legs of narrower frame through the
opening between the cross bar and top of the
wider frame. To complete this step and align the
bolt holes, you will need to tip the narrow frame
side to side to pass the cross bar through the
opening of the wider frame. For assembly as-
sistance, go to the product information page at
www.milwaukeetool.com.
5. Lay the assembly on its side and align the bolt
holes, placing the plastic spacer between the
frame sections, as shown.
6. Insert the long bolt through the wider frame,
spacer, and narrower frame and secure with the
nut. Use a 6 mm hex wrench and an adjustable
(or 17 mm open end) wrench to securely tighten.
7. Screw the nut onto the adjustable foot (the nut
may come factory assembled)
8. Screw in the adjustable foot into the stand until the
stand sits level. Turn the nut back until it contacts
the frame, locking the adjustable foot in place.
2
Long Bolt,
Spacer, & Nut
Crossbar
1
2
1
3
2