Descargar Imprimir esta página

Panasonic AJ-WM50P Instrucciones De Funcionamiento página 2

Publicidad

Idiomas disponibles

Idiomas disponibles

Specifications
Power supply
5 V DC (
External dimensions
16 mm (W) x 8 mm (H) x 41 mm (L)
(Excluding the cap)
(5/8 inch x 5/16 inch x 1-5/8 inch)
Weight (Excluding the cap) Approx. 4.3 g (0.01 lb)
Antennas temperature
Tx1, Rx1
Interface
USB 2.0
Standards
IEEE802.11a/b/g/n/ac Compliant
Transmission Formats
OFDM, DSSS
Frequency Range
2412 MHz - 2462 MHz (channels 1 - 11)
(Channel)
5180 MHz - 5240 MHz (W52)
5745 MHz - 5825 MHz (W58)
Data Transfer Speed
IEEE802.11ac Max. 433 Mbps
(standard value *
1
)
IEEE802.11n Max. 144 Mbps
IEEE802.11a/g Max. 54 Mbps
IEEE802.11b Max. 11 Mbps
Access Format
Infrastructure Mode
Ad Hoc Mode *
Security
WPA2-PSK (TKIP/AES)
WPA-PSK (TKIP/AES)
WEP (64 bit/128 bit)
*
1
This is a theoretical speed, and the actual transfer speed may vary depending
on factors such as the usage environment and connection products.
*
2
IEEE802.11n is not supported.
Note
Depending on the P2 device or the projector into which this product is inserted, some
modes may not function.
) (power supplied via USB2.0 bus)
2
For Users in U.S.A.
Important Safety Notice
Panasonic
Model AJ-WM50P
FCC ID: ACJAJ-WM50P
Supplier's Declaration of Conformity
Model Number:
AJ-WM50P
FCC ID:
ACJAJ-WM50P
Trade Name:
Panasonic
Responsible party:
Panasonic Corporation of North America
Address:
Two Riverfront Plaza, Newark, NJ 07102
Support Contact:
1-800-524-1448
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
FCC Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• The user may find the booklet "Something About Interference" helpful, which is
available from FCC local regional offices.
Warning: To assure continued FCC emission limit compliance, follow the attached
installation instructions. Also, any unauthorized changes or modifications to this
equipment could void the user's authority to operate this device.
FCC RF Exposure Warning:
• This transmitter complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
• This transmitter may not be co-located or operated with any other antenna or
transmitter.
• This transmitter has been approved for portable operation and requires minimum
0.5cm spacing be provided between antennas and all person's body (excluding
extremities of hands, wrist and feet) during wireless modes of operation.
15 of the FCC Rules. These limits are

Publicidad

loading