Makita PDC01 Manual De Instrucciones página 12

Unidad portátil de alimentación eléctrica
Ocultar thumbs Ver también para PDC01:
Tabla de contenido

Publicidad

Using the adapter pocket
CAUTION:
Do not use this unit with the cord
fixed using the hook and loop fastener of the
adapter pocket.
You can put the adapters into the adapter pocket as
shown in the figure.
► Fig.6: 1. Adapter 2. Adapter pocket
► Fig.7: 1. Adapter 2. Adapter pocket
ASSEMBLY
CAUTION:
Always be sure that the unit is
switched off and the battery cartridge is removed
before carrying out any work on the unit.
Assembling the unit
1.
Attach the battery box to the base plate as shown
in the figure. Be sure to lock the levers on both sides of
the base plate after attaching the battery box.
► Fig.8: 1. Lever 2. Battery box 3. Base plate
CAUTION:
Make sure that the battery box is
securely fixed to the base plate, and locked with
levers. Otherwise, the battery box may fall when you
wear the unit or use the unit, and cause an injury.
2.
Adjust the position of the waist belt. Pull up the
height adjustment lever, then adjust the position of the
waist belt by sliding the base plate, and then return the
lever.
► Fig.9: 1. Height adjustment lever 2. Base plate
3. Waist belt
NOTICE:
If the height adjustment lever is loose,
tighten the nut of the height adjustment lever.
When tightening the nut, do not tighten it excessively.
Otherwise, the height adjustment lever will not move.
► Fig.10: 1. Nut
3.
Attach the adapter pocket to the waist belt with the
hook and loop fastener as shown in the figure.
► Fig.11: 1. Adapter pocket
NOTE: The adapter pocket can be attached on either
left or right side of the waist belt.
4.
Adjust the width of the shoulder harness using the
width adjustment belt.
► Fig.12: 1. Width adjustment belt
5.
Wear the unit, then lock the buckle of the waist
belt, and then adjust the length of the waist belt.
► Fig.13: 1. Buckle
NOTE: You can fold and fix the belt with the hook and
loop fastener as shown in the figure.
► Fig.14: 1. Belt
6.
Adjust the length of the shoulder harness.
► Fig.15: 1. Shoulder harness
NOTE: You can fold and fix the belt with the hook and
loop fastener as shown in the figure.
► Fig.16: 1. Belt
OPERATION
CAUTION:
When wearing the unit, be sure
to put shoulder harness on your both shoulders.
Otherwise, the unit may fall when you wear the unit or
use the unit, and cause an injury.
CAUTION:
When wearing the unit, be sure to
wear the unit on your back. Otherwise, the unit may
fall during operation and cause an injury.
CAUTION:
Always switch off the tool or
machine before turning on the unit, or connecting
the plug of the adapter to the socket of the battery
box. Otherwise, the tool or machine may start sud-
denly and cause an injury.
Connecting the unit to the tool or
machine
1.
Pull out the cord from either left or right side of the
battery box. When pulling out the cord, be sure to set
the cord in the holders as shown in the figure.
► Fig.17: 1. Cord 2. Holder
2.
Wear the unit.
3.
Insert the plug of the adapter into the socket of the
battery box all the way so that the arrow mark on the
plug is aligned with that on the socket.
► Fig.18: 1. Plug 2. Socket 3. Arrow mark
NOTICE:
When disconnecting the plug and
socket, do not hold the cords but hold the plug
and socket. Otherwise, the cords may be damaged
and cause a malfunction of the unit.
NOTE: The plug and socket are disconnected if a
certain load is applied.
4.
Install the adapters to the tool or machine in the
same way as the battery cartridge.
► Fig.19: 1. Adapter
NOTICE:
For 18 V battery-powered tool or
machine, use the adapter for 18 V. For 36 V
(18 V x 2) battery-powered tool or machine, use
the adapters for 36 V (18 V x 2).
NOTICE:
If you cannot install the adapters to
the tool or machine when installing two adapters,
swap one adapter with the other adapter and
install them.
► Fig.20: 1. Adapter
NOTE: The direction of the cord of the adapter can be
changed in the range of approximately 180 degrees.
5.
Press the power button to turn the power on. To
turn the power off, press the power button for a few
seconds.
► Fig.21: 1. Power button
12 ENGLISH

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

191a59-5

Tabla de contenido