General Information; Operating Conditions - Hameg Instruments HM8011-3 Manual De Operación

General information

The operator should not neglect to carefully read
the following instructions and those of the
mainframe HM8001, to avoid any operating errors
and to be fully acquainted with the module when
later in use.
After unpacking the module, check for any
mechanical damage or loose parts inside. Should
there be any transportation damage, inform the
supplier immediately and do not put the module
into operation.
This plug-in module is primarily intented for use in
conjunction with the Mainframe HM8001. When
incorporating it into other systems, the module
should only be operated with the specified supply
voltages.
Safety
This instrument has been designed and tested in
accordance with IEC Publication 1010-1, Safety
requirements for electrical equipment for
measurement, control, and laboratory use. It
corresponds as well to the the CENELEC
regulations EN 61010-1. All case and chassis parts
are connected to the safety earth conductor.
Corresponding to Safety Class 1 regulations (three-
conductor AC power cable). Without an isolating
transformer, the instruments power cable must be
plugged into an approved three-contact electrical
outlet, which meets International Electrotechnical
Commission (IEC) safety standards.
Warning!
Any interruption of the protective conductor
inside or outside the instrument or
disconnection of the protective earth terminal
is likely to make the instrument dangerous.
Intentional interruption is prohibited.
The istrument must be disconnected and secured
against unintentional operation if there is any
suggestion that safe operation is not possible. This
may occur:
• if the instrument has visible damage,
• if the instrument has loose parts.
• if the instrument does not function,
• after long storage under unfavourable
circumstances (e.g. outdoors or in moist
environments),
• after excessive transportation stress (e.g. in
poor packaging).
When removing or replacing the metal case, the
instrument must be completely disconnected from
the mains supply. If any measurement or calibration
procedures are unavoidable on the opened-up
instrument, these must only be carried out by
qualified personnel acquainted with the danger
involved.
12
Symbols as Marked on Equipment
ATTENTION refer to manual.
DANGER High voltage.
Protective ground (earth) terminal.

Operating conditions

The ambient temperature range during operation
should be between +10°C and +40°C and should
not exceed -40°C or +70°C during transport or
storage. The operational position is optional,
however, the ventilation holes on the HM8001 and
on the plug-in modules must not be obstructed.
Warranty
Before being shipped, each plug-in module must
pass a 24 hour quality control test.
Provided the instrument has not undergone any
modifications Hameg warrants that all products of
its own manufacture conform to Hameg
specifications and are free from defects in material
and workmanship when used under normal
operating conditions and with the service conditions
for wich they were furnished.
The obligation of HAMEG hereunder shall expire
two (2) years after delivery and is limited to
repairing, or at its option, replacing without charge,
any such product which in Hamegs sole opinion
proves to be defective with the scope of this
warranty.
This is Hamegs sole warranty with respect to the
products delivered hereunder. No statement,
representation, agreement or understanding, oral
or written, made by an agent, distributor,
representative or employee of, which is not
contained in thiss warranty will be binding upon
Hameg, unless made in writing and executed by
an authorized Hameg employee. Hameg makes no
other warranty of any kind whatsoever, expressed
or implied, and all implied warranties of
merchantibility and fitness for a particular use which
exceed the aforestated obligation are hereby
disclaimed by Hameg be liable to buyer, in contract
or in tort, for any special, indirect, incidental or
consequential damages, espresses, losses or
delays however caused.
In case of any complaint, attach a tag to the
instrument with a description of the fault observed.
Please supply name and department, address and
telephone number to ensure rapid service.
The instrument should be returned in its original
packaging for maximum protection. We regret that
transportation damage due to poor packaging is not
covered by this warranty.
Änderungen vorbehalten / Subject to change without notice