Purpose Of This Manual; User Safety - Xylem Rule GPH Serie Manual De Instrucciones

Purpose of this manual

The purpose of this manual is to provide necessary information for product installation, operation and
maintenance.
CAUTION: Read this manual carefully before installing, using or servicing this product.
Failure to follow the instructions within this manual could result in explosion, property damage,
severe personal injury and/or death.

User safety

General safety rules
• Always keep work area clean
• Pay attention to the risks presented by gas and vapors in the work area
• Avoid all electrical dangers. Pay attention to the risks of electric shock or arc flash hazards
• Always bear in mind the risk of drowning, electrical accidents and burn injuries
WARNING: This pump is designed for use with fresh water and salt water ONLY. Use
with any other hazardous, caustic, or corrosive material
and the surrounding environment, possible exposure to hazardous substances and injury.
Potential electrical sources of ignition located in spaces containing gasoline powered machinery,
or gasoline fuel tank(s), or joint fitting(s), or other connection(s) between components of a gasoline
system, shall be ignition protected, unless the component is isolated from a gasoline fuel source as
described in ABYC E-11.5.3.3.
Exception:
1. Boats using diesel fuel as the only fuel source.
2. Outboard engines mounted externally or in compartments open to the atmosphere in
accordance with the requirements of ABYC H-2, Ventilation of Boats Using Gasoline.
The bilge pump inlet shall be located so that excess bilge water can be removed from the bilge at static
floating position, and at maximum conditions created by the boat's motion, heel, and trim.
Electrical
Disconnect power before installing or servicing the pump.
Our pump is equipped with silicone blocked, tin coated 16 gauge (1.5 mm
table below when extending the wires.
Recommended Wire Size
Total Wire Length (positive to pump to ground) — feet (meters)
0 – 6 ft 6 – 10 ft
(0 – 1.8 m) (1.8 – 3 m)
16 AWG 14 AWG
(1.5 mm 2 ) (2.5 mm 2 )
The electrical wiring, connections, and installation shall be in accordance with the requirements of ISO
10133, ABYC E-11, AC and DC Electrical Systems On Boats.
could result in damage to the pump
2 ) wire. Please follow the
10 – 15 ft 15 – 30 ft 30 – 40 ft
(3 – 4.6 m) (4.6 – 5.5 m) (5.5 – 12.2 m)
12 AWG 10 AWG 8 AWG
(4 mm 2 ) (6 mm 2 ) (10 mm
2
This pump must be fused as follows:
GPH (LPH)
800 (3028)
1100 (4164)
800 (3028)
1100 (4164)
All potential sources of ignition located in spaces containing gasoline powered machinery or gasoline
fuel tank(s), or joint fitting(s), or other connection(s), between components of a gasoline system,
shall be ignition protected in accordance with the requirements of ISO 10133, ABYC E-11, AC and DC
Electrical Systems On Boats.
The electrical wiring, connections, and installation shall be in accordance with the requirements of ISO
10133, ABYC E-11, AC and DC Electrical Systems On Boats.
CAUTION: Disconnect power from the system before working on the unit to avoid personal
injury, damage to the surrounding environment and/or damage to the unit.
CAUTION: Always install proper fuse size to prevent damage to product should a short occur.
Failure to install proper fuse could increase risk of pump malfunction, potentially resulting in
personal injury and/or fire hazard.
CAUTION: Keep all wire connections above the highest water level. Wires must be joined
with butt connectors and a marine grade sealant to prevent wire corrosion.
Direct to Battery
2 )
Amps Amps
Volts
(Volts) (Volts)
12 Volts
12 2.9 (12) 3.5 (13.6)
12 3.7 (12) 4.5 (13.6)
24 Volts
24 1.5 (24) 1.8 (27)
24 1.8 (24) 2.2 (27)
Grey wire Fuse
Black wire
3
Fuse Size
5 A
7.5 A
4 A
4 A