General Safety Warnings; Personal Safety - Dremel Idea Builder 3D40 Instrucciones De Funcionamiento

DM 2610039151 01-16_3D40 1/7/16 9:33 AM Page 3
Read all instructions in this manual and familiarize yourself with the
Dremel 3D40 before setup and use. Failure to comply with the warnings
WARNING
and instructions may result in fire, equipment damage, property damage, or personal
injury.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
Work Area Safety
Keep work area clean and well lit. Cluttered
or dark areas invite accidents.
Do not operate Dremel 3D40 in the
presence of flammable liquids, gases or
dust.
Dremel
temperatures which may ignite the dust or
fumes.
Store idle 3D40 out of reach of children
and other untrained persons. Injury can
occur in hands of untrained users.
Electrical Safety
Always use the Dremel 3D40 with a
properly grounded outlet. Do not modify
Dremel 3D40 plug. Improper grounding and
modified plugs increase risk of electric shock.
Do not use Dremel 3D40 in damp or wet
locations. Do not expose Dremel 3D40 to
rain. Presence of moisture increases risk of
electric shock.
Do not abuse the cord. Never use the cord
for pulling or unplugging the Dremel 3D40.
Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or
entangled cords increase the risk of electric
shock.
Avoid using this product during an
electric storm. There may be a remote risk
of a power surge from lightning that may
result in electric shock hazard.
In case of emergency unplug Dremel 3D40
from outlet.

Personal Safety

Stay alert, watch what you are doing and
use common sense when operating a
Dremel 3D40. Do not use Dremel 3D40
while you are tired or under the influence
of drugs, alcohol or medication. A moment
of inattention while operating Dremel 3D40
may result in personal injury.
Use personal protective equipment. The
use of protective equipment such as heat
resistant gloves and safety glasses will
reduce the risk of personal injuries.

General Safety Warnings

READ ALL INSTRUCTIONS
3D40 creates high
Dress properly. Do not wear loose clothing
or jewelry. Keep your hair, clothing and
gloves away from moving parts. Loose
clothes, jewelry or long hair can be caught in
moving parts.
Dremel 3D40 Use and Care
Before every use check Dremel 3D40 for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the Dremel 3D40's
operation. If damage is suspected have
the Dremel 3D40 repaired by authorized
Dremel service center before use. Use of
Dremel 3D40 when damaged may result in
poor quality of object creation, further
equipment damage, property damage or
personal injury.
Do not touch the extruder tip during
Dremel 3D40 operation or until it has
cooled down to at least 60°C (140°F).
Contact with the extruder tip during or after
operation before tip has cooled may result in
personal injury.
Set up the Dremel 3D40 in a well-ventilated
area. Place Dremel 3D40 printer on flat
nonflammable surface and away from
flammable materal. Provide at least 8
inches of unobstructed spacing around
Dremel 3D40. Dremel 3D40 melts plastic
during building. Plastic odors emitted during
Dremel 3D40 operation may irritate eyes and
airways. Locating Dremel 3D40 close to
surrounding objects prevents proper
ventilation.
Do not reach inside the Dremel 3D40 while
it is in operation. Contact with Dremel 3D40
moving parts during operation may result in
poor build quality, equipment damage or
personal injury.
Always monitor the Dremel 3D40 during
operation. Use of Dremel 3D40 by persons
unfamiliar with these warnings and
instructions may result in equipment or
property damage and personal injury.
3