Power Supply; Operating Mode - Desoutter ECP190 Manual Del Usuario

Ocultar thumbs Ver también para ECP190:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 12
6159932900
Issue no: 15
Original instructions.
© Copyright 2019, Ets Georges Renault
44818 St Herblain, FR
All rights reserved. Any unauthorized use
or copying of the contents or part thereof
is prohibited. This applies in particular to
trademarks, model denominations, part numbers
and drawings. Use only authorized parts. Any
damage or malfunction caused by the use of
unauthorised parts is not covered by Warranty or
Product Liability.
DECLARATION OF USE
"Class I" tool. Tool suitable for industrial
environment only. It shall be used for tightening
joints in wood, metal or plastic material. No other
use will be permitted. For a reversible tool, the
anticlockwise direction is for loosening only.
DATA
(See page 4).
Noise level: < 70 dB(A) (EN 60745).
Vibration level: < 2.5 m/s² (EN 60745).
Working temperature : 0 / +60°C.
Humidity ratio : 0 / 90%.
Declaration of noise and vibration emission
All values are current as of the date of this
publication. For the latest information please visit
desouttertools.com.
These declared values were obtained by
laboratory type testing in accordance with the
stated standards and are suitable for comparison
with the declared values of other tools tested
in accordance with the same standards. These
declared values are not adequate for use in risk
assessments and values measured in individual
work places may be higher. The actual exposure
values and risk of harm experienced by an
individual user are unique and depend upon
the way the user works, the workpiece and the
workstation design, as well upon the exposure
time and the physical condition of the user.
We, Desoutter, cannot be held liable for the
consequences of using the declared values,
instead of values reflecting the actual exposure,
in an individual risk assessment in a work place
situation over which we have no control.
This tool may cause hand-arm vibration
syndrome if its use is not adequately managed.
An EU guide to managing hand-arm vibration
can be found at http://www.pneurop.eu/uploads/
documents/pdf/PN3-02-NV_Declaration_info_
sheet_0111.pdf
We recommend a programme of health
surveillance to detect early symptoms which
may relate to noise or vibration exposure, so
that management procedures can be modified to
help prevent future impairment.
8 / 56

POWER SUPPLY

This tool has to be used with controllers of the
Desoutter range only.

OPERATING MODE

This tool will only work with firmware
release 4.5 and above.
The stall bar must be installed on the
ECP tool before tightening. The reaction
bar must be appropriate to the assembly.
Refer to the diagram explaining how
to use it. Be careful not to catch your
fingers between the stall bar and the
obstacle used for the torque control.
1. Fit the tool with a suitable socket, then
connect it to the power supply by means of
the controller.
2. Select the appropriate program on the
controller.
3. Hold the tool by means of the handle and
apply to the fastener to be tightened.
In manual mode, the motor will start only when
the trigger is operated.
When using a suspension ring, make sure that it
is in good condition.
As the reaction force increases in
proportion to the tightening torque, make
sure that the tool is in perfect working
order and the controller is programmed
correctly, to reduce the risk of injury to
the operator as a result of unexpected
behaviour of the tool.
INSTRUCTIONS FOR REVERSING
(See page 6).
Never shift the gear when the machine
is running.
● To switch to loosening mode (1)
(anticlockwise rotation), push the reversing
ring (A) by hand, and turn it anticlockwise
(C) until the red arrow is visible and the
ring clicks into position. The reversing ring
then remains in this position. The red arrow
indicates the direction of rotation.
● To switch to tightening mode (3) (clockwise
rotation), turn the reversing ring clockwise (B)
until the green arrow is visible and the ring
clicks into position. The reversing ring then
remains in this position. The green arrow
indicates the direction of rotation.
● If the reversing ring is placed in an
intermediate position (2), the device is out
of gear and the drive spindle can easily be
turned to the desired position.
01/2019

Publicidad

Tabla de contenido
loading

Tabla de contenido