Configure "My Stations; Configure "My Streams; Remote Unit Advanced Buttons - Rotel RT-12 Manual De Instrucciones

English
After logging into your account, you will be able to edit your information
for 'My Stations', 'My Streams', 'My Podcast' and 'My Radios'.
Follow the instructions on the website to personalize your menu.
Configure "My Stations"
There are an enormous choice of stations that are available in the
database from the website. Please follow instructions on the website to
search for stations. When search results are displayed, there will be a
link to 'Add to my stations', Click on this and the station selected will be
added to My Stations. A new top level menu 'My Stuff' will appear on
the display, with a sub-menu 'My Stations'.
After the initial registration, you can add to 'My stations' while connected
to a radio station by pressing the REPLY key. The display will ask if you
want to add selection to 'My stations' press the push select knob to add
selection.
Configure "My Streams"
While logged into your website account, you can add your own internet
radio streams to the 'My Streams' section which will be listed under 'My
Account'.
Click on 'My Streams', a prompt will appear to enter the station's name
and its media stream URL. The media stream URL should be a link to the
website's actual audio stream. .
Note: 'My Stuff' menu and stations under 'My Stations','My Streams'
will appear after the unit has updated the stations list. Please power
OFF then ON and enter 'Internet Radio' from the top level menu for the
unit to update the stations list.

Remote Unit Advanced Buttons

Setup menu
To enter the setup menu, press the SETUP
and you will see the following display:
< 1 POWER OPTION >
2 DIMMER
3 FACTORY DEFAULT
4 VERSION
5 ANTENNA SELECT
6 SIPORT UPGRADE
7 DISPLAY CONTRAST
8 EXIT
1. POWER OPTION, select between NORMAL or QUICK. In NORMAL
mode, the network connection is turned OFF when the unit is in STANDBY.
This consumes less power in STANDBY mode. Setting this to QUICK
leaves the network connection active during STANDBY mode. Use QUICK
mode if you are controlling the unit using the IP Remote control through
the Rotel Link sockets.
u
C button on the remote control
2. DIMMER controls the brightness of the front panel display, it can be
dimmed with seven steps. You can access this control directly with the
DIM button on the remote control.
3. FACTORY DEFAULT sets the unit into the original state as when it left
the factory. Presets and network configurations will be lost, and sets the
remote code to 1 (see below).
4. VERSION shows this unit's software version.
5. ANTENNA SELECT choose AUTO(default), FM or DAB antenna.
6. SIPORT UPGRADE is used to upgrade the software that controls the FM
and DAB features of this unit. This should not be used by the end user.
7. DISPLAY CONTRAST can be used to adjust the contrast on the front
panel display. Step through the vaious steps with the LEFT/RIGHT buttons
on the remote and find the one that best suits you.
8. EXIT, exits the setup menu. Or push the SETUP
remote at anytime to EXIT.
Second Amplifier Code
The factory setting is remote code 1. If you find that the remote is conflicting
with other Rotel amplifiers, you can change to remote code 2 with the
following steps:
1. While pointing the remote at the unit, press on the remote control 'FM'
N , release, then immediately press '2'
key for 5 seconds. The unit will show 'Audio Custom Code 1--> 2'. The
unit is now changed to Audio remote code 2.
2. You must now change the remote to output code 2. To do this ,press
'FM' and '2' at the same time, then release both keys.
N H
3. Repeat the above procedure and press '1' key instead of '2' to change
the unit back to Code 1.
Second CD Code
The factory setting is CD code 1, but the transport buttons
pause) used in Network mode may conflict with other Rotel CD players
in your system. You can change the CD codes by following the steps
below.
1. While pointing the remote at the unit, press on the remote control
'NETWORK' , release, then immediately press '2'
N
press the '2' key for 5 seconds. The unit will show 'CD Custom Code
1--> 2'. The unit is now changed to CD remote code 2.
2. You must now change the remote to output code 2. To do this ,press
'NETWORK' N and '2' H at the same time, then release both keys.
3. Repeat the above procedure and press '1' key instead of '2' to change
the unit back to Code 1.
17
C button on the
H and continue to press the '2'
J (play, stop
and continue to
H