Adjust Lcd Backlighting; Enable/Disable The Record Lamp; Adjust Lcd Contrast; Adjust Microphone Sensitivity - Philips Digital Pocket Memo LFH 9600 Manual Del Usuario

D Note: When voice-activated recording is enabled, the voice
activation recording (sensitivity) level can be adjusted during
recording by using the + or
level meter indicates the threshold value.
E Tip: The performance of the voice-activated recording feature
depends largely on the microphone sensitivity setting and the
noise level of the environment. See
on page 15 for more information.
6.4

Adjust LCD backlighting

The LCD screen of the Digital Pocket Memo can be backlit while
dictating in a poorly illuminated environment. The backlight
consumes more power, so it can disabled when it is not necessary.
The 4-position slide switch (12) must be in the
1
Press the MENU button to open the menu.
2
Press the + or - buttons (5) to highlight the
3
and press the ENTER smart button.
Press the + or - buttons to highlight the
4
and press the ENTER smart button.
Press the + or - buttons to select the your preference
5
SEC ON, 20 SEC ON).
Press the OK smart button (2a) to save the setting or press the
6
CANCEL smart button (2b) leave the setting unchanged.
Press the BACK smart button (2a) twice to exit the menu.
7
6.5

Enable/disable the record lamp

When enabled, the status LED/record lamp shines red (overwrite
mode) or green (insert mode) during recording.
Follow these steps to disable the record lamp:
The 4-position slide switch (12) must be in the
1
Press the MENU button to open the menu.
2
Press the + or - buttons (5) to highlight the
3
and press the ENTER smart button.
Press the + or - buttons to highlight the
4
item and press the ENTER
Press the + or - buttons to select the your preference (ON,
5
OFF).
Press the OK smart button (2a) to save the setting or press the
6
CANCEL smart button (2b) leave the setting unchanged.
Press the BACK smart button (2a) twice to exit the menu.
7
6.6

Adjust LCD contrast

The contrast of the LCD screen can be adjusted for the level of light
in your environment and your viewing preferences.
The 4-position slide switch (12) must be in the
1
Press the MENU button to open the menu.
2
Press the + or - buttons (5) to highlight the
3
and press the ENTER smart button.
Press the + or - buttons to highlight the
4
and press the ENTER smart button.
Press the + or - buttons to adjust the contrast.
5
Press the OK smart button (2a) to save the contrast setting
6
or press the CANCEL smart button (2b) to leave the setting
unchanged.
Press the BACK smart button (2a) twice to exit the menu.
7
User manual
- buttons. A triangle at the volume

Adjust microphone sensitivity

STOP position.
SETUP menu item
BACKLIGHT menu item
(OFF, 8
STOP position.
SETUP menu item
RECORD LAMP
smart button.
STOP position.
SETUP menu item
CONTRAST menu item
6.7 Adjust microphone sensitivity
Set the microphone sensitivity for the environment and your
dictation preferences. Consider these factors:
• What is your voice level while dictating?
• How far is the microphone from your mouth?
• How noisy is the environment?
The 4-position slide switch (12) must be in the
1
Press the MENU
2
Press the + or -
3
and press the ENTER
Press the + or -
4
item and press the
Press the + or -
5
(DICTATE, PRIVATE, CONFERENCE).
Press the OK smart button (2a) to save the setting or press the
6
CANCEL smart button (2b) to leave the setting unchanged.
Press the BACK
7
6.8

Change sound feedback

The Digital Pocket Memo can be set to give sound feedback (beeps)
when:
• the end of the file is reached during playback
• an index mark is hit during fast forward or fast rewind
• the battery level drops below 10%
• available memory drops below two minutes
• a command cannot be carried out, or
• a barcode is scanned (with the optional barcode module).
To change this setting:
The 4-position slide switch (12) must be in the
1
Press the MENU
2
Press the + or -
3
and press the ENTER
Press the + or -
4
item and press the
Press the + or -
5
menu feedback.
Press the OK smart button (2a) to save the setting or press the
6
CANCEL smart button (2b) to leave the setting unchanged.
Press the BACK
7
6.9

Change noise reduction

Activate this function when in playback mode for recordings with
significant background noise. This feature reduces the level of
interfering background noise.
The 4-position slide switch (12) must be in the
1
Press the MENU
2
Press the + or -
3
and press the ENTER
Press the + or -
4
menu item and press the
Press the + or -
5
reduction.
Press the OK smart button (2a) to save the setting or press the
6
CANCEL smart button (2b) to leave the setting unchanged.
Press the BACK
7
button to open the menu.
buttons (5) to highlight the SETUP
smart button.
buttons to highlight the MICROPHONE
ENTER smart button.
buttons to select the your preference
smart button (2a) twice to exit the menu.
button to open the menu.
buttons (5) to highlight the SETUP
smart button.
buttons to highlight the DEVICE BEEP
ENTER smart button.
buttons to enable (ON) or disable (OFF) sound
smart button (2a) twice to exit the menu.
button to open the menu.
buttons (5) to highlight the SETUP
smart button.
buttons to highlight the NOISE REDUCTION
ENTER smart button.
buttons to enable (ON) or disable (OFF) noise
smart button (2a) twice to exit the menu.
STOP position.
menu item
menu
STOP position.
menu item
menu
STOP position.
menu item
15