Emerson BTAS Serie Instrucciones De Funcionamiento

Suction line Filter drier shell Suction line Filter drier shell
General information:
ALCO BTAS suction line filter drier shell with
replaceable core is for new installation and
integrating into the systems after compressor
burnout, retrofit and maintenance.
• BTAS is only for installation in suction line.
Warning: Do not use BTAS on liquid line
applications.
!
Safety instructions:
• Read installation instruction
Failure to comply can result in device failure,
system damage or personal injury.
• It is intended for use by persons having the
appropriate knowledge and
attempting to install the shell make sure
pressure in system is brought to and remains at
atmospheric pressure.
• Do not release any refrigerant into atmosphere.
• Do not use any other fluid media without prior
approval of Alco Controls. Use of fluid not
listed could result in:
− Change of hazard category of product and
consequently change of
assessment requirement for product in
accordance with European
equipment directive 97/23/EC
− Chemical deterioration of desiccants of core
in the shell
• In a severely contaminated system, avoid
breathing acid vapours and avoid contact with
skin from contaminated refrigerant / lubricants.
Failure to do so could result in skin injury.
• The filter dryer shell must be used only for the
purpose it is designed for.
Mounting location:
• Allow sufficient clearance from the flanged end to
permit removal of the shell's entire internal
components assembly (see fig. 1).
Technical Data
Maximum working pressure at Ts: –45°C to +50°C
Volume (liter)
Fluid group
Refrigerants: CFC, HCFC, HFC
Connection
Required cores (1 piece)
Hazard category: PED 97/23/EC
Marking
BTAS_65045__R06
Operating Instructions Operating Instructions
BTAS
• Shell must be as close as possible to the Shell must be as close as possible to the
compressor in suction line but upstream of any compressor in suction line but upstream of any
vibration adsorber that might be presented. vibration adsorber that might be presented.
• The shell must be installed as shown in Figure 2, 3 The shell must be installed as shown in Figure 2, 3
or 4 which permits oil return to the compressor and or 4 which permits oil r
convenient location for removing of core or convenient location for removing of core or
cartridge. cartridge.
• Remark: Protect the shell against sunrays and Remark: Protect the shell against sunrays and
vibration. vibration.
• For For detailed detailed
recommendation, consult the system / compressor recommendation, consult the system / compressor
thoroughly.
manufacturers or contact Alco controls application manufacturers or contact Alco co
engineering department. engineering department.
Installation: Installation:
• Do not remove seal caps until ready for installation Do not remove seal caps until ready for installation
skill. Before
in order to minimise entering of moisture and dirt in order to minimise entering of moisture and dirt
into shell. into shell.
• The arrow on the label must be point in the The arrow on the label must be point in the
direction of refrigerant flow. Reverse direction of refrigerant flow. Reverse flow reduces
the filtering ability, increases the pressure drop the filtering ability, increases the pressure drop
through the filter drier shell and may cause internal through the filter drier shell and may cause internal
screen damage. screen damage.
• Use proper temperature for brazing of copper to Use proper temperature for brazing of copper to
brass as the entire shell and fittings are solid brass. brass as the entire shell and fittings are solid brass.
conformity
• If the total shell If the total shell weight results in excessive stress
to the piping joints, the shell must be supported by to the piping joints, the shell must be supported by
pressure
suitable mounting bracket(s). suitable mounting bracket(s).
• It is recommend to insulate the entire shell in order It is recommend to insulate the entire shell in order
to reduce heat gain of suction gas. to reduce heat gain of suction gas.
• The new gasket (F) is supplied with filter core The new gasket (F) is supplied with filter core or
filter drier cartridge. Lubricate the new gasket (F) filter drier cartridge. Lubricate the new gasket (F)
sparingly with refrigerant oil. (Fig. 5) sparingly with refrigerant oil. (Fig. 5)
• Remove the flange bolts (A), flange cover (C), Remove the flange bolts (A), flange cover (C),
spring (D) and discard the flange gasket (F). spring (D) and discard the flange gasket (F).
• Place the new gasket (F) in groove at the top of Place the new gasket (F) in groove at the top of
shell (G). shell (G).
• Remo Remove the filter core or filter drier cartridge (E)
from packaging and assemble as fast as possible to from packaging and assemble as fast as possible to
minimise moisture contamination. minimise moisture contamination.
Type:
Replacement for 05 placement for 05
Emerson Climate Technologies GmbH Emerson Climate Technologies GmbH
GB
Holzhauser Str. 180 - D-13509 Berlin
www.emersonclimate.eu www.emersonclimate.eu
clean clean-up procedure and
BTAS-2... BTAS-3...
Ps: 24 bar Ps: 24 bar
0.42 1.2
II II
16...22 mm 28...54 mm
A2F / A2F-D A3F / A3F-D
not applicable not applicable
HP, UL, HP, UL,
Date: 20.06.2013
13509 Berlin
Germany
• Install the filter core or filter drier cartridge (E) Install the filter core or filter drier cartridge (E)
with the closed end toward the flange cover (C). with the closed end toward the flange cover (C).
• With the large diam With the large diameter of spring (D) against
flange cover (C), push the flange cover (C) against flange cover (C), push the flange cover (C) against
the shell (G). Align cover (C) careful inside gasket the shell (G). Align cover (C) careful inside gasket
(F) (Fig. 5)
• Install two flange bolts (A) in diagonally opposite Install two flange bolts (A) in diagonally opposite
holes to hold the cover snugly against the shell holes to hold the cover snugly against the shell
(G).
• Install the remaining flange bolts. ll the remaining flange bolts.
• Tighten all flange bolts (A) evenly in a criss Tighten all flange bolts (A) evenly in a criss-cross
pattern to the following maximum torque: pattern to the following maximum torque:
BTAS-2.. 16 Nm 2.. 16 Nm BTAS-4.. 27 Nm
BTAS-3.. 19 Nm 3.. 19 Nm BTAS-5.. 68 Nm
Leakage test:
• After completion of installation, a test After completion of installation, a test pressure
must be carried out as follows: must be carried out as follows:
- According to EN378 for systems which must According to EN378 for systems which must
comply comply with with European European pressure pressure
directive 97/23/EC 97/23/EC
- To maximum working pressure of system for other To maximum working pressure of system for other
applications
Warning:
1) Failure to do so could result in loss 1) Failure to do so could result in loss of refrigerant
and person injury.
2) The pressure test must be conducted by skilled 2) The pressure test must be conducted by skilled
persons with due respect regarding the danger persons with due respect regarding the danger
related to pressure.
Operation:
• Start the compressor and put the system in Start the compressor and put the system in
operation. Record the pressure drop on the operation. Record the pressure drop on the
enclosed label and attach to the side of shell (G). d label and attach to the side of shell (G).
Service hints
Caution: Do not attempt to dry out a used core.
: Do not attempt to dry out a used core.
BTAS-4... BTAS
Ps: 24 bar Ps: 24 bar
2.0 2.0
II II
35...67 mm 35...67 mm
A4F / A4F A4F-D
not applicable not applicable
HP, UL HP, UL, UL,
PCN 862 630 PCN 862 630
equipment equipment
BTAS-5...
Ps: 24 bar
3.2
II
54...80 mm
A5F / A5F-D
I
,
PA-00309