Ecco EC2028-WC Instrucciones De Instalación página 2

CAMERA
Image
Voltage Requirement
Effective Pixels
Power Consumption
Lens Size
Lens Angle
Audio
Light Sensor
Infrared LEDs
Housing
Mech. Vibration
Mounting
Weight
Dimensions (WxHxD)
Operating Temp.
IP Rating
Approvals
Current Consumption
Video Delay
Frame Rate
System
Caution!
!
When drilling into any vehicle surface, make sure that the area is free from any electrical wires, fuel lines, vehicle
upholstery, etc. that could be damaged.
Notes:
1. Larger wires and tight connections will provide longer service life for components. For high current wires it is
recommended that terminal blocks or soldered connections be used with shrink tubing to protect the connections. Do
not use insulation displacement connectors (e.g., 3M Scotchlock type connectors)
2. Route wiring using grommets and sealant when passing through compartment walls. Minimize the number of splices
to reduce voltage drop. High ambient temperatures (e.g., under-hood) will significantly reduce the current carrying
capacity of wires, fuses, and circuit breakers. All wiring should conform to the minimum wire size and other
recommendations of the manufacturer and be protected from moving parts and hot surfaces. Looms, grommets,
cable ties, and similar installation hardware should be used to anchor and protect all wiring.
3. Fuses or circuit breakers should be located as close to the power takeoff points as possible and properly sized to
protect the wiring and devices.
4. Particular attention should be paid to the location and method of making electrical connections and splices to protect
these points from corrosion and loss of conductivity.
5. Ground termination should be only be made to substantial chassis components, preferably directly to the vehicle
battery.
6. Circuit breakers are very sensitive to high temperatures and will "false trip" when mounted in hot enviroments or
operated close to their capacity.
EC2028-WC
1/3 CCD
12-32V
628(H) x 582(V)
5W
1/4"
120°Horizontal/90 Vertical
No
Auto Switch B&W
18
Aluminum Alloy
8g
Rear/Front
1.20 lbs / 0.54kg
(L) 90x (W) 60.5x (T) 56.5 mm
-4°F to 158°F / -20 to +70 oC
IP66
FCC,CE,RoHS
500mA Max
150ms
25fps
PAL
MONITOR
Screen Size
Controller
Voltage
Power
Mirror Imaging
Resolution
System
Viewing Angle
Visible Area
Contrast
Split Screen Feature
AV Compatible
DVR Compatible
Audio
Brightness
Light Sensor
Camera Selection
Connection: CAM
Connection (Monitor Pigtail)
Housing
Mounting
Mech. Vibration
Weight
Dimensions (WxHxD)
Operating Temp
Remote Control
Approvals
Trigger voltage
Distance
EC7000B-WM
7" (4:3) and (16:9)
4 Camera
12-32 VDC
Approximate: 7W
Yes (via Camera and Monitor Switch)
800 (W) x RGB x 480 (H)
PAL/NTSC
L/R/U/D: 60º/60º/45º/60º
154X86mm
400:1
Quad View Split Screen
No
No
No
400cd/m2
Auto Dim
1-4 Via Trigger Wires
DC plug/2 wire
Male 6pin/5 wire
Plastic
Pedestal
Pedestal Bracket - 3G
1.50 lbs / 0.67kg
176(W) x 123(H) x 27(D)mm
-4°F to 158°F / -20 to +70 oC
Yes
FCC,CE,RoHS
12 - 32V
30 - 100 meters
Page 2 of 6