Gemini FX-7000 Manual Del Operador página 2

AC 15V: Use this input to connect the power, plug the adapter into an outlet and the AC 15V (1) input.
1
POWER: To turn on the POWER (2), press this switch once.
2
BALANCED OUTPUT: Use the BALANCED OUTPUT (3) to connect to your amplifiers BALANCED input.
3
MASTER OUTPUT: An unbalanced output to connect to your amplifiers input.
4
ZONE OUTPUT: Connect this line to an additional amplifier or powered speakers.
5
REC OUTPUT: To record a mix, connect this line to a recording device.
6
SEND: An output used to send your mix to an outboard signal processor.
7
RETURN: An input that receives a signal from your outboard signal processor.
8
LINE 5 INPUT: To connect any line in devices, such as a CD Player, DAT, MiniDisc, etc.
9
PH3/L4 INPUT (PHONO3/LINE4): To connect a TURNTABLE or LINE input into the mixer.
10
LINE 3 INPUT: SEE LINE 9
11
PH2/L2 INPUT (PHONO2/LINE2): SEE LINE 10
12
PH1/L1 INPUT (PHONO1/LINE1): SEE LINE 10
13
MIC 2: Plug in your second MICROPHONE here.
14
PHONO/LINE SWITCH: Controls what kind of device is heard on the PH3/L4 (10) input.
15
PHONO/LINE SWITCH: Controls what kind of device is heard on the PH2/L2 (12) input.
16
PHONO/LINE SWITCH: Controls what kind of device is heard on the PH1/L1 (13) input.
17
GROUND SCREW: Connect your ground wire from your turntable here.
18
MIC 1: Plug in the main MICROPHONE here.
19
HEADPHONES: Plug in your HEADPHONES in here, to listen to your mix.
20
CROSSFADER CURVE: Pressing this button changes the CROSSFADER (23) curve from gradual to sharp.
21
X-FADER ASSIGN: Use to select CHANNEL 1 or 2, for which channel is assigned to the left side of the CROSSFADER (23).
22
CROSSFADER: Shifting the CROSSFADER (23) from left to right will enable you to mix different channels.
23
CROSSFADER REVERSE SWITCH: This reverses the location of the channels assigned to the CROSSFADER (23).
24
DSP EFFECT: Press DSP EFFECT (25) to turn the effect on or off that is being chosen.
25
CHANNEL 1 SLIDE: Moving this slide up or down raises and lowers the volume for CHANNEL 1.
26
CHANNEL 2 SLIDE: Moving this slide up or down raises and lowers the volume for CHANNEL 2.
27
CHANNEL 3 SLIDE: Moving this slide up or down raises and lowers the volume for CHANNEL 3.
28
CUE CH1: Press CUE CH1 (29) to hear CHANNEL 1 thru the HEADPHONES.
29
CUE CH2: Press CUE CH2 (30) to hear CHANNEL 2 thru the HEADPHONES.
30
CUE CH3: Press CUE CH3 (31) to hear CHANNEL 3 thru the HEADPHONES.
31
CUE EFF: Press CUE EFF (32) to hear the effect that is being applied to CHANNELS 1-3, MIC 1 or the MASTER (PGM)
32
with the HEADPHONES.
CH-1 SWITCH: Flipping this switch changes the CHANNEL 1 input from MIC 2 to PH1/L1.
33
CH-2 SWITCH: Flipping this switch changes the CHANNEL 2 input from PH2/L2 to L3.
34
CH-3 SWITCH: Flipping this switch changes the CHANNEL 3 input from PH3/L4 to L5.
35
LOW: Controls the LOW (Bass) range for the channels.
36
MID: Controls the MID (Middle) range for the channels.
37
HIGH: Controls the HIGH (Treble) range for the channels.
38
GAIN: Controls the overall volume GAIN for each of the channels.
39
VU METER: The VU METER (40) displays the LEFT & RIGHT CHANNEL levels or the CUE and PGM.
40
VU METER MODE: Press VU METER MODE (41) button to change the VU METER (40) mode.
41
CUE SPLIT: Pressing CUE SPLIT (42) lets you hear the CUE on the left side earphone and the PGM on the right side.
42
CUE-PGM: Turning CUE-PGM (43), from left to right changes the monitored CUE to PGM (MASTER).
43
CUE LEVEL: CUE LEVEL (44) controls the level of the CUE.
44
MASTER: MASTER (45) controls the level of the MASTER OUTPUT (4) & BALANCED OUTPUT (3).
45
ZONE: ZONE (46) controls the level of the ZONE OUTPUT (5).
46
MIC 1/TALKOVER: MIC 1/TALKOVER (47) switch activates MIC 1 (19) and TALKOVER.
47
MIC 1/TALKOVER LED: The MIC 1/TALKOVER LED (48) glows when the MIC 1/TALKOVER (47) switch is on.
48
MIC1 LEVEL: MIC 1 LEVEL (49) controls the volume of MIC 1 (19).
49
LOW: For adjusting the BASS level on MIC 1 (19).
50
HIGH: For adjusting the TREBLE level on MIC 1 (19).
51
CHANNEL SELECTOR: Moving the CHANNEL SELECTOR (52) will assign CHANNELS 1-3, MIC 1 or the MASTER
52
(PGM) that the DSP SIGNAL PROCESSOR is affecting. Use CUE EFF (32) to hear the effect before pressing.
EFFECT SELECTOR: Turn this knob to select 1-16 effects.
53
DSP EFFECTS: Here is the list of effects, refer to DSP SIGNAL PROCESSOR section for details.
54
PARAMETER LED DISPLAY: PARAMETER LED DISPLAY (55) displays the chosen effect and the parameters.
55
PARAMETER KNOB: PARAMETER (56) knob changes the parameters (1-99) of the chosen effect.
56
WET/DRY: Turning the WET/DRY (57) knob lets you activate the effects signal in and out of the mix.
57
QUICK START GUIDE:
(2)