Identification Number; Lock Function - Monacor JTS IN-64TB Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

5) Confirm the selection with the button SET.
will be shortly displayed and the unit will go to nor-
mal operation.
5.1.2 REMOSET transmission
The REMOSET function (frequency adjustment of the
transmitter via a radio signal of the receiver) will be
activated/deactivated for the transmitter.
1) Keep the button SET (4) pressed for approx. 2 sec -
onds until the display shortly shows
the group adjusting mode (group indication , , or
will flash).
2) In the group adjusting mode, press the button SET
twice to go to the adjusting mode for the REMOSET
transmission. The display will show:
with the REMOSET function activated
with the REMOSET function deactivated
Note: To exit the adjusting mode without making an
adjustment, press the button SET repeatedly until the
display shows
operation.
3) To deactivate the REMOSET function, press the
button - (5); to activate the REMOSET function,
press the button + (6).
4) Confirm the selection with the button SET.
will be shortly displayed and the unit will go to nor-
mal operation.

5.1.3 Identification number

To allow the REMOSET transmission between the
transmitter and the receiver, the identification numbers
of the units must be matched.
1) Keep the button SET (4) pressed for approx. 2 sec -
onds until the display shortly shows
the group adjusting mode (group indication , , or
will flash).
2) In the group adjusting mode, press the button SET
three times to go to the adjusting mode for the iden-
tification number. The display will show
identification number currently adjusted.
Note: To exit the adjusting mode without making an
adjustment, press the button SET repeatedly until the
display shows
operation.
3) To run through the adjusting range
, use the button - (5) for downward selection
and the button + (6) for upward selection. Use the
corresponding button to adjust the same identifica-
tion number on the transmitter as on the receiver
(the transmitter will only respond to the REMOSET
signal of the receiver with the same identification
number) or select the adjustment
10
and then
. The unit will then return to normal
and then
. The unit will then return to normal
,
(the trans-
mitter will then respond to the REMOSET signal of
any receiver).
4) Confirm the selection with the button SET.
will be shortly displayed and the unit will go to nor-
mal operation.

5.1.4 Lock function

In the factory, the lock function of the unit has been
deactivated.
When the lock function is activated, the frequency
adjustment via the REMOSET function will not be pos-
sible. Furthermore, it will not be possible to switch off
the transmitter: when the power switch (2) is set to
"ON", the display will show
Activating the lock
1) Keep the button SET (4) pressed for approx. 2 sec -
onds until the display shortly shows
the group adjusting mode (group indication , , or
will flash).
2) In the group adjusting mode, press the button SET
four times to go to the adjusting mode for the lock
function. The display will show
Note: To exit the adjusting mode without making an
adjustment, press the button SET. The display will show
and the unit will return to normal operation.
3) To activate the lock, press the button + (6).
will be displayed.
4) Confirm the selection with the button SET.
will be shortly displayed and the unit will go to nor-
mal operation.
Deactivating the lock
1) The power switch (2) must be set to "ON".
2) Keep the button SET (4) pressed for approx. 3 sec -
onds until
3) To deactivate the lock, press the button - (5).
will be displayed.
4) Confirm the selection with the button SET.
and the
will be shortly displayed and the unit will go to nor-
mal operation.
...
("lock on").
("lock off").
is displayed.
and then

Publicidad

Tabla de contenido
loading

Tabla de contenido