chocking or strangling hazards for the
child. To avoid strangling hazards, do
not give to your child or place near him,
objects equipped with cords.
· A prolonged exposure to the sun may
cause changes of tones to the product's
colour. After a prolonged exposure of the
product to high temperatures, wait a few
minutes prior to placing your child in it.
· When not in use, keep the product away
from the reach of children.
COMPONENTS
A. Support leg with wheels
B. Support leg with non-slip feet
C. Central supporting structure
D. Fixing belts
E. Fabric lining
F. Mattress with removable cover
G. Upper tubular structure
H. Upper removable tubular structure
I. Bag
A1) Height adjuster button
A2) Removable structure support
A3) Height indicator
A4) Feet rotation release button
A5) Adjustable feet
A6) Wheels with brake
B1) Non-slip feet
B2) Structure fixing for central support
C1) Fixing pin
C2) Fabric lining fixing button
C3) Grey fixing buckles
D1) Red anchoring buckles
E1) Belt with clip
E2) Pocket
E3) Zip for fabric removal
E4) Zip for co-sleeping opening
E5) Mesh window
E6) Side support for restraint
G1) Leg fixing
H1) Removable tubular structure release button
L) Maximum limit for mattress height
ASSEMBLY OF THE CRIB
1. Hold the support leg making sure that the external tube slides
upwards until you hear the locking CLICK in the first position
(fig. 1). Repeat the same operation with the other support leg.
2. Fix the central supporting structure to the 2 legs as illustrated
in figure 2. The CLICK of the pivot indicates correct fixing of the
structure (fig. 4). WARNING: make sure that the grey buckles
are on the same side as the adjustable feet (fig. 4).
3. Assemble the upper structure and the fabric to the legs,
sliding the tube of the leg inside the side pocket of the fabric
(fig. 5). Carry out this operation for both sides.
4. Subsequently fix the upper structure to the legs, inserting
the relative plastic support as illustrated in figure 6. Push
downwards until you hear the CLICK of correct fixing (fig. 7).
Carry out this operation for both sides.
5. Fix the fabric lining to the central structure, hooking the 2
belts with clips positioned at the bottom of the lining (fig. 8).
6. Position the mattress on the bottom of the crib (fig. 9).
7. Lock the 2 wheels of the crib, lowering the levers that activate
the brakes (fig. 10).
At this point the crib is ready to be used. WARNING: check to
make sure that all of the fasteners have been correctly attached
and that the zips are closed and locked right to the end of
their travel. WARNING: do not use the cot with adjustable
feet partially or totally rotated and unlocked (fig. 11). The
correct position for use is illustrated in figure 12. In the case of
accidental knocks against adjustable feet, return them to the
correct position by lifting the crib slightly.
HEIGHT ADJUSTMENT OF THE COT
The crib can be adjusted to different height positions. In order
to adjust the height, pull the adjustment lever upwards and lift
the crib to the desired position (fig. 13). Repeat this operation
on the opposite side.
The base of the crib can be inclined slightly by adjusting the 2
legs to different heights (fig. 14). WARNING: the crib can be
inclined with a maximum variance of 2 positions between one
leg and the other (for example: the right leg in position 3 and
the left leg in position 1, see fig. 15). WARNING: The head of the
child should always be positioned on the highest side (fig. 16).
CO-SLEEPING MODE (FIXING TO THE BED)
The crib can be fixed to the parent's bed (co-sleeping mode).
WARNING – IMPORTANT FOR THE SAFETY OF YOUR CHILD:
this method is only possible with bed types that comply with all
of the conditions described in this paragraph.
In particular the side support of the crib should always be put
close to the parent's mattress and the mattress should always
be aligned with the height of the side support for restraint of the
crib (see fig. 17). Furthermore, the crib should be firmly fixed
to the structure of the parents bed or to the mattress support
(net or slats).
WARNING: Check to make sure that the crib in the co-sleeping
mode does not interfere with the parent's bed.
WARNING: During use, make sure that the parents bed sheets,
blankets etc. do not enter and cover the interior of the crib.
8. Open the side of the crib with the window using the side zips
and open them completely (fig. 18).
9. Then press the removable tubular structure release button
and remove partially on one side and then on the other (fig.
19). Once this operation has been performed on both sides,
remove the tube and fix it to the legs of the structure using the
relative supports (fig. 20). WARNING: use the crib with the tube
lowered, only in the co-sleeping mode.
10. Move the crib close to the parent's bed and check the height
of the crib compared with the mattress of the bed. WARNING:
the height of the parent's mattress should always be more
than that of the side support for containment of the crib (fig.
21). WARNING: in the co-sleeping mode the 2 legs of the crib
should always be adjusted to the same height.
11. In order to fix the crib to the parents bed (co-sleeping mode)
use the pair of straps provided. The straps can be found in the
lower pocket of the fabric lining (fig. 22).
12. Fix the grey buckles underneath the fabric lining on both
sides. Make sure that the red buckles are positioned above the
strap belt as illustrated in figure 23.
13. Subsequently fix the belt around the structure of the
parent's bed, from the bottom towards the top (fig. 24) and fix
19